Post on 16-Nov-2015
description
Configuracin Gateway GSM DinStar DWG2000C-Elastix Se muestra el paso a paso Les para configurar gateway GSM en elastix usando troncales SIP. El esquema de red es el siguiente:
Datos: Servidor Elastix: IP:192.168.1.35 con Servidor de DHCP habilitado. Gateway GSM: IP: 192.168.1.34 con SIM: 96566016 Computador con 2 Softphone: IP: 192.168.1.33. Anexo en 3CX: 3001 Anexo en Zoiper: 3002 Configuracin de anexos:
En 3CX:
En Zoiper:
CONFIGURACIN ELASTIX Paso 1: Se crea una nueva troncal SIP apuntando hacia el Gateway GSM en la ruta PBX>Troncales>AddTrunk>Add SIP Trunk Trunk Name: celular_dwg_1 Trunk Name: celular_dwg_1 PEER Details: host= 192.168.1.34 context=from-trunk type=peer insecure=port,invite Se guardan los cambios (Submit Changes, Apply Configuration)
Paso 2: Se crea una nueva Ruta Saliente usando el patrn de marcado deseado (en este caso ser con el prefijo 3 de la siguiente forma 3XXXXXXXXX) apuntando hacia la troncal anteriormente creada (PBX>Rutas Salientes>Add Route) Route Name: celular_dwg_1 PIN Set: None Dial Patterns: 3 - X. Trunk Sequence: 0 SIP/ celular_dwg_1 Se guardan los cambios (Submit Changes, Apply Configuration)
Antes de configurar la ruta entrante se debe crear un IVR para habilitar las llamadas desde celular hacia Elastix de la siguiente forma:
Ir a PBX PBX Configuration Grabaciones del Sistema. Usted observar la siguiente pantalla:
Grabamos un audio que nos enve a dos opciones para los dos anexos.
Desde la extensin 3001 marque *77, usted escuchar un beep, despus de esto grabe su mensaje y marque # para finalizar.
Acto seguido escuchar la voz de Asterisk indicndole opciones para escuchar el mensaje o para re grabarlo de nuevo. Si usted est satisfecho con el resultado simplemente cuelgue.
Despus nombraremos a la grabacin como "bienvenida" y guardamos. Luego aadimos un IVR
Para crear un IVR debemos ir a PBX PBX Configuration IVR y hacemos clic en
Aadir IVR Nombramos bienvenida al IVR y configuramos 2 opciones una para cada anexo. Una vez configurado hacemos clic en guardar y aplicamos los cambios.
Otra alternativa es configurar una cola para habilitar en la ruta entrante de la siguiente forma: Nombre de la cola: colast01 Agentes fijos: 3001,0 3002,0 Poltica de Ringado: Aleatorio
Una vez configurado hacemos clic en guardar y aplicamos los cambios.
Paso 3: Se crea una nueva Ruta Entrante para enrutar las llamadas entrantes, en nuestro caso se enrutarn hacia el IVR Bienvenida o la cola colast01, se usar el CID 96566016 para identificar las llamadas entrantes (PBX>Rutas Entrantes>Add Incoming Route) DID Number: 96566016 Set Destination: IVR: Bienvenida Se guardan los cambios (Submit Changes, Apply Configuration)
CONFIGURACIN GATEWAY DINSTAR DWG2000C Paso 5: Se configura la direccin IP Gateway DinStar (Network Configuration>Local network) Use the following IP address IP Address: 192.168.1.34 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.35 (Ntese que esta es la direccin IP del servidor Elastix)
Se crea un IP Trunk apuntando hacia nuestro servidor Asterisk (IP Trunk Configuration>IP Trunk>Add) Index: 31 IP: 192.168.1.35 Port: 5060 Description: colast01
Paso 6: Se configura el modo de enrutamiento (Routing Configuration>Routing Parameter) IP->Tel Parameter: Route calls before manipulation Tel->IP parameter: Route calls before manipulation
Paso 7: Se configura el enrutamiento para llamadas desde Celular hacia Elastix (Routing Configuration>Tel->IP Routing>Add) Index: 0 Description: default Source Prefix: any Source: Port: Any Destination Prefix: any Destination: IP: 31
Paso 8: Se configuran los permisos para las llamadas desde Elastix hacia Celular (Operation>IP->Tel Operation) Index: 31 Source Prefix: any Source IP: IP: 31 Destination Prefix: any Operation: Allow Call Description: colast01_out
Paso 9: Se configuran los permisos para las llamadas desde Celular hacia Elastix (Operation>Tel->IP Operation)
Index: 31 Source Prefix: any Source Port: Port: Any Destination Prefix: any Operation: Allow Call Auto Call: Habilitar Description: colast01_in
Paso 10: Se configuran las opciones del servicio (System Configuration>Service Parameter) Local Start RTP Port: 8000 Enable silence suppression: Yes Call Progress Tone: USA Preferred Coders: PCMU, PCMA, G729AB, G723.1 Voice Frames per Tx: 2 Do Not Answer GSM incoming Call for Hotline: Yes Enable GSM Incoming Configuration: Yes Auto Outgoing Routing Type: Polling IP to GSM One Stage Dialing: Yes Answer Delay: 5 Redirect Call When All Ports Busy: No Play Voice Prompt for GSM incoming Calls: Yes DTMF Parameter DTMF Method: RFC2833 RFC2833 Payload Type: 101 DTMF Volume: 0dB DTMF interval: 200 NAT Transversal: Disable Other Configuration Enable Private Service: Yes User ID is Phone Number: Yes Only Accept Calls from SIP Server: No Allow Call from GSM to IP without Registration: Yes Allow Call from IP to GSM without Registration: Yes Reject Anonymous call from IP to GSM: No Use # as End Key: Yes No Answer TimeOut: 55 Interdigit Timeout: 4 Call Delay: 0
Paso 11: Se configuran las opciones de la cuenta SIP (System Configuration>SIP Parameter) SIP Proxy SIP Server Address: 192.168.1.35 SIP Server Port: 5060 Check Status: No Outbound Proxy Outbound Proxy Address: Outbound Proxy Port: 5060 Is Register: No DNS Query type: A query DNS refresh interval: 0 T1: 500 T2: 4000 T4: 5000 TMAX: 32000 Keepalive Interval: 32 Enable 100rel: No From mode when Caller ID is Available: Tel/Tel From mode when Caller ID is Unavailable: Username Answer Mode: Answered
183 Mode: Immediately Session timer: No
Paso 12: Se configuran los parmetros de los puertos (System Configuration>Port Parameter>Detail) All Ports register used same user ID: Yes SIP User ID: Authenticate ID: Authenticate Password: Local SIP Port: 5060 Tx Gain: +2dB Rx Gain: +6dB To VOIP Hotline: 96566016 (Este es el nmero que enviamos a Elastix para la ruta de entreda To PSTN Hotline: Auto-Dial Delay Time. 0
Con esto hemos finalizado la configuracin, ahora se reinicia el Gateway y se realizan pruebas de llamadas entrantes y salientes