Post on 22-Apr-2017
BEFORE YOU BEGIN
�
�
�
Please read these instructions carefully to familiarizeyourself with the required tools, materials, andinstallation sequences. Follow the sections that pertainto your particular installation. This will help you avoidcostly mistakes. In addition to proper installation, readall operating and safety instructions.All information in these instructions is based upon thelatest product information available at the time ofpublication. Kohler China reserves the right to makechanges in product characteristics, packaging, oravailability at any time without notice.These instructions contain important care, cleaning, andwarranty information-please leave instructions for theconsumer.
ORDERING INFORMATION
ODEON Wall-hung Toilet ....................................K-8752TIncludes Bowl .......................................................K-8750TIncludes Seat .....................................................K-8741T-*
-1-
NOTES
�
�
�
�
�
�
�
�
�
Observe all local plumbing and building codes.
Shut off the water supply.
Seat post holes are on 155mm centers.
Passageways is 60mm.
Water depth from rim is 210mm.
Ensure that the new drain and shut-off valve have the
correct roughing-in dimensions. .
Be very careful while working with vitreous china products.
Vitreous china can break or chip if the bolts or nuts are
overtightened, or if carelessly handled.
Carefully inspect the new bowl for any sign of damage.
Fixture dimensions are nominal and conform to tolerances
established by ASME Standards (A112. 19.2M).
See Fig.#1
TOOLS AND MATERIALS REQUIRED(Not supplied)
� 254mm adjustable wrench
Metal file (file cut)
Tape measure
Tubing cutter
Level
Hacksaw
Putty knife
Screwdriver
Straight pipe coupling
Connection packing
�
�
�
�
�
�
�
�
�
1037407-T01-A
ODEON
INSTALLATION INSTRUCTIONS
VITREOUS CHINA WALL-HUNG P-TRAP TOILETK-8752T
�
�
�
-
�
�
�
�
�
�
�
�
�
�
254mm
...................................................K-8752T..............................................................K-8750T
.....................................................K-8741T-*
�
�
�
�
�
�
�
�
�
155mm
60mm
210mm
1
ASME(A112.19.2M)
�
�
, 2007
Copyright Kohler China Ltd., 2007
528137
430
180358 156 268
361
540
-2-
ROUGHING-IN
P-trap K-8750T Unit: mm:
20
55
106
222
323
356
20
398
54
Fig.#1 1
1037407-T01-A
INSTALLATION
1. INSTALL THE TANK
Turn the water supply off before installing the new toilet.
Install the concealed tank system in wall beforedecorating the wall.
Install the tank system per tank's installation instructions.
Recommended tanks (Fig.#2-a)Kohler Inwall Tank 6284T-NA (With iron rank)
�
�
�
And Inwall Tank cover 6283T-**
Recommended sensorKohler ODEON TOUCHLESS TOILET SENSOR K-744TRecommended rank dimension(Fig.#2-b)1) Rank height should be adjust between 0~200mm.2) Rank should support weight 400kg.
Fig.#2-a
2-a1.
( 2-a)6284T-NA ( )
6283T-**
K-744T( 2-b)
1) 0~200mm2) 400kg
�
�
�
Fig.#2-b
2-b
400kg400 10
300
135
35
180
2. SET THE SPACING OF THE BOWLAfter you install the tank, be careful to set the spacing of thebowl on wall according to the dimensions as shown.
2.
3. ATTACH CONNECTION PIPE
Attach pipe with gasket to the inlet to link to the concealedtank.
Attach pipe with gasket to the outlet.*Apply gasket for sealing the bowl to wall.
You may apply some lubricant to help connect smoothly.
3.
*
�
�
�
�
�
�
Fig.#4 4
Fig.#3 3
-3-
Inlet
Outlet
180 2
135
2
220
330
1
Carrier Studs
25 2
Unit: mm
1037407-T01-A
-4-
4. INSTALL THE NEW BOWL
Apply a little silicone sealant along the edge, to fill the gap
between bowl and wall.
4.
5a
See Fig. 5a.
Fig. #5a 5a
1
Fig. #5b 5b
Fig. #5c 5c Fig. #5d 5d
Place the new bowl on the wall through the carrier. Wrench
the nut to tighten and make them attached securely.
Torque for tightening nuts is recommended to be within
the range from 8 Nm to 12 Nm.
5b
8Nm 12Nm
See Fig. 5b.
�
�
Adjust to horizontal and finish tightening.
5c
See Fig. 5c. Apply sealant to make sure the bowl's edge seals to the wall.
5d
See Fig. 5d.
1037407-T01-A
-5-
5. INSTALL SEAT WITH HARDWARE PROVIDED.
5. 6
See Fig. #6.
4Hand tighten nuts.
6Finish tightening.
5Adjust seat fit.
Fig. #6 6
1037407-T01-A
CONSUMER RESPONSIBILITIES
When cleaning up after installation, do not use abrasivecleansers, as they may scratch and dull the toilet surface.Use warm water and a liquid detergent to clean the surface.
Remove stubborn stains, paint, or tar with turpentine or paintthinner. Do not allow cleaners containing petroleum distillatesto to remain in contact with any toilet surface for long periodsof time.
Remove plaster by carefully scraping with a wood edge. Donot use metal scrapers, wire brushes, or other metal tools.Use a powder type detergent on a damp cloth to provide mildabrasive action to any residual plaster.
Clean the outside surface of your vitreous china product withmild soap and warm water. Wipe the entire surfacecompletely dry with a clean, soft cloth.
Most toilet bowl cleaners are not harmful to the vitreous chinasurface of the toilet bowl. Please follow the bowl cleanermanufacturer is instructions carefully.
Do not use abrasive cleaners or solvents.
-6-1037407-T01-A
ODEON
SERVICE PARTS PAGE
VITREOUS CHINA WALL-HUNG P-TRAP TOILETK-8752T
1021447Right Hand Hinge
K-8741T-**Odeon Seat
1021448HardwareAssy
1021449Screw
1021446Left Hand Hinge
**** Color code must be specified when ordering.
K-8752T
K-8741T-**
-7-1037407-T01-A