CUADRO DE MANDO PARA PUERTAS, PERSIANAS …...Cuadro de control monofásico de 220 V AC para...
Transcript of CUADRO DE MANDO PARA PUERTAS, PERSIANAS …...Cuadro de control monofásico de 220 V AC para...
CHAMELEON R+A: ROLLER SHUTTERS, DOORS AND AWNINGS
1
CUADRO DE MANDO PARA PUERTAS,
PERSIANAS ENROLLABLES Y TOLDOS
Cuadro de control monofásico de 220 V AC para puertas, persianas
enrollables y toldos, con receptor incorporado multi marca y multi frecuencia
RX-Multi integrado. Entradas de pulsador arriba/abajo configurables como
hombre presente, orden directa o pulsador secuencial, entrada de
seguridad, finales de carrera y pulsador secuencial. Con cierre automático
disponible y entrada de fotocélula.
CONEXIONES
CHAMELEON R+A: ROLLER SHUTTERS, DOORS AND AWNINGS
2
CONFIGURACIÓN DIP
1 FC / HOMBRE PRESENTE
ON Pulsador Hombre presente (en bornes Común, Apertura y
Cierre).
OFF Finales de carrera (en bornes Común, Apertura y Cierre).
2 HOMBRE PRESENTE EN APERTURA (DIP 1 ON)
ON Para realizar la maniobra de apertura es necesario
mantener pulsado el emisor o pulsador PROG. Si no se mantiene,
la maniobra se detiene.
OFF Orden directa durante la apertura.
3 HOMBRE PRESENTE EN CIERRE (DIP1 ON)
ON Para realizar la maniobra de cierre es necesario mantener
pulsado el emisor o el pulsador PROG. Si no se mantiene, la
maniobra se detiene.
OFF Orden directa durante el cierre.
4 FOTOCÉLULA
ON Inhabilita la fotocélula (No es necesario puentear la entrada
de Seguridad). Con esta configuración el cierre automático no
está disponible en la programación.
OFF Habilita la fotocélula para su conexión. Mediante
programación se puede configurar el modo automático.
PROGRAMACIÓN
MENÚ DE PROGRAMACIÓN
OPCIÓN 1 - MODO MEMORIZACIÓN DE MANDOS
Pulsar PROG hasta escuchar 1 pitido que indica que se ha
seleccionado el modo memorización para programar un emisor.
OPCIÓN 2 - MODO PROGRAMACIÓN TIEMPO MANIOBRAS
Pulsar PROG hasta escuchar 2 pitidos indicando que está en modo
programación de tiempos de maniobra. Donde se configura el
recorrido de la puerta.
CHAMELEON R+A: ROLLER SHUTTERS, DOORS AND AWNINGS
3
OPCIÓN 3 - BORRADO DE CANAL
Pulsar PROG hasta escuchar 3 pitidos que indican que está en modo
borrado de canal grabado. Se borrará el canal y sonará un pitido de
confirmación.
OPCIÓN 4 - (DIP 1 ON) OPCIÓN 4 - (DIP 1 OFF)
UP-DOWN/PULSADOR SECUENCIAL
Pulsar PROG hasta escuchar 4
pitidos que indican opción
up/down, al soltar el botón, se
cambiará automáticamente a
pulsador secuencial y vice-versa.
Un pitido corto indica la selección
up/down, uno largo pulsador
secuencial.
PASO A PASO/INVERSIÓN CIERRE
Pulsar PROG hasta escuchar 4
pitidos indicando que se
encuentra en la opción inversión
al cierre. Al soltar el botón pasará
automáticamente al mo-do
inversión al cierre y viceversa.
Un pitido corto indica la
selección paso a paso, uno largo
inversión al cierre.
OPCIÓN 5 - BORRADO DE MEMORIA
Pulsar PROG hasta escuchar 5 pitidos que indican que está en modo
borrado de todos los canales y de mandos. Se borrará al soltar el
pulsador.
*Nota: una vez borrada la memoria hay que repetir la opción 1 y 2
OBLIGlATORIAMENTE para el correcto funcionamiento.
MEMORIZACIÓN MANDOS
Seleccionar la opción 1 del MENÚ: Pulsar PROG hasta escuchar 1 pitido que
indica que se encuentra en modo memorización.
Pulse el botón del mando que quiera utilizar, tres pitidos cortos confirmarán la
memorización.
El cuadro sale automáticamente del modo memorización una vez
transcurridos 4 segundos, o bien pulsando de nuevo el botón PROG o
pulsando un mando ya programado anteriormente, la salida se indica con
3 pitidos.
PROGRAMACIÓN DE TIEMPOS DE MANIOBRA
Antes de iniciar la programación, comprobar que los finales de carrera
están bien instalados (en caso de que se instalen). La puerta debe estar
cerrada.
Las ordenes se realizan mediante pulsación de PROG o de un mando
previamente programado.
1. Seleccionar la opción 2 del MENÚ: Pulsar PROG hasta escuchar 2
pitidos (Se ha activado el modo programación de tiempos de
maniobra).
CHAMELEON R+A: ROLLER SHUTTERS, DOORS AND AWNINGS
4
2. La puerta comenzará la maniobra de apertura. Si se han
seleccionado los finales de carrera, parará por el final de carrera de
apertura, si no, dar la orden al final de la maniobra.
3. Una vez finalizada la maniobra de apertura, el cuadro espera una
orden para comenzar la maniobra de cierre. Si se da la orden dentro
de un intervalo de 5 segundos, se activa el modo manual; si se activa
pasados esos 5 segundos, se configura el modo de cierre
automático y el tiempo transcurrido desde el final de la maniobra de
apertura hasta que se inicia la maniobra de cierre es el tiempo de
pausa establecido.
*En el caso de que la fotocélula esté DESHABILITADA (DIP 4 ON):
No funciona la programación por cierre automático, solo
manual(por motivos de seguridad).
*En el caso de que la fotocélula esté HABILITADA, pero el usuario
no la instale: La placa se bloquea y no permite realizar ninguna
maniobra de cierre, indicando que hay un error en la
configuración.
4. La puerta se detendrá si los finales de carrera están instalados, por
contacto del final de carrera de cierre. Se escuchará un pitido para
indicar el fin de la maniobra de cierre y la salida de la programación
de tiempos de maniobra.
Repetir el procedimiento si se desea modificar la programación.
CHAMELEON R+A: ROLLER SHUTTERS, DOORS AND AWNINGS
5
ROLLER SHUTTERS, DOORS AND
AWNINGS CONTROL BOARD
Control single-phase box for door, roller shutter and awnings, designed for
tubular motor. The power supply is 220 V AC. With receiver multibrand and
multifrequency RX-Multi integrated, up/down switch input (configurable as
dead man, direct order or sequencial switch), limit switches and sequencial
switch. Photobeam security signal input available and automatic
programmable closure.
CONNECTIONS
CHAMELEON R+A: ROLLER SHUTTERS, DOORS AND AWNINGS
6
SETTING DIP CONFIGURATION
1 LIMIT SWITCHES /DEAD MAN
ON Dead man (for terminal Common, Open and Close).
OFF Limit switches (for terminal Common, Open and Close).
2 DEAD MAN IN OPENING MANEUVER (DIP 1 ON)
ON To start the opening maneuver, press the transmitter or the
switch. If the button is not held, the maneuver stops.
OFF Opening is set as direct order operation.
3 DEAD MAN IN CLOSING MANEUVER (DIP1 ON)
ON To start the closing maneuver, press the transmitter or the
PROG button. If the button is not held, the maneuver stops.
OFF Closing is set as direct order operation.
4 PHOTOBEAM
ON Photocell is disabled (It is not neccessary to
bridge the security input). Automatic closure is not available at
this position.
OFF Photobeam is enabled. This configuration allows the
programmation of optional automatic closure.
PROGRAMMATION
PROGRAMATION MENU
OPTION 1 – REMOTE MEMORIZATION MODE
Press PROG until 1 beep sounds that means remote memorization mode is
activated. Now you can learn the remote.
OPTION 2 - MANEUVERS TIME PROGRAMMING
Press PROG until 2 beeps sound that means it is on maneuvers time
programming.
CHAMELEON R+A: ROLLER SHUTTERS, DOORS AND AWNINGS
7
OPTION 3 - CHANNEL ERASE
Press PROG until 3 beeps sound that means it is on delete of learnt
channel.
OPTION 4 (DIP 1 ON) OPTION 4 (DIP 1 OFF)
UP-DOWN / SEQUENTIAL SWITCH
Press PROG until 4 beeps sound that
means up/down option. When the
button is realised, menu changes to
alter switch and viceversa.
One long beep means alter switch
and a short beep means up/down
selection.
STEP BY STEP/INVERSION TO CLOSURE
Press PROG until 4 beeps sound that
means it is selected inversion to
closure option menu. When the
button is realised, menu changes to
inversion to closure and viceversa.
One long beep means inversion to
closure selection and a short beep
means step by ste
OPTION 5 –ERASE MEMORY
Press PROG until 5 beeps sound that selects channels and remotes delete
mode. Release to delete.
*Note: once the memory have been deleted, you have to repeat again the
option 1 and 2 obligatorily for correct working.
REMOTE LEARNING
Select option 1 from the MENU (Press PROG until 1 beep sounds that means it
is on remote memorization mode).
Press the button on the remote that you want to use, 3 short beeps will confirm
it is memorized correctly.
Control board ends the memorization mode by pressing again button PROG,
a remote previously learnt or after 4 seconds, 3 beeps indicate when it is out.
MANEUVERS TIME PROGRAMMING
Before programming, check limit switches in case they are installed. The door
should be closed.
The orders are given by pressing the remote previously installed or the PROG
button.
1. Select Option 2 from the MENU (Press PROG until 2 beeps sound this
means maneuver programming starts).
2. The opening maneuver starts. If limit switches have been installed,
maneuver ends by the opening limit switch contact, if not, the order must
be given at the end of the maneuver.
3. Control board awaits for the starting of closure maneuver. If it is activated
within 5 seconds, manual mode will be activated; if it is pressed after that 5
seconds, automatic closing mode will be set, the time spent from the end
of opening to closing maneuver starts, it is the pause time programmed.
CHAMELEON R+A: ROLLER SHUTTERS, DOORS AND AWNINGS
8
*In case photobeam is DISABLED (DIP 4 ON): The automatic closure is
not available at programming maneuver option from the menu (for
security issues).
*In case photobeam is ENABLED (DIP 4 ON) but not installed by the user:
No closure will be made, so the user can notice the configuration is
mistaken. And the door can not work.
4. If limit switches have been installed door stops by closing limit switch
contact. If not, an order is required. A beep indicates the end of closing
maneuver and maneuver time programming finishes.
Repite the procedure if the maneuvers are not programmed correctly.
ITEM DIP POSITION COMPATIBLE
BRAND
FREQUEN
CY COMMENTS
1
ABC remote 433.92
MHz
2
Clemsa
Mastercode
433.92
MHz
CHAMELEON R+A: ROLLER SHUTTERS, DOORS AND AWNINGS
9
3
DOOYA 433.92
MHz
4
FAAC SLH
Rolling Code
433.92
MHz
5
FAAC SLH 868.3 MHz
6
Hormann
Marantec
Berner
868.3 MHz
7
Jolly Motors 433.92
MHz
8
Liftmaster 315 MHz
9
Liftmaster 390 MHz
CHAMELEON R+A: ROLLER SHUTTERS, DOORS AND AWNINGS
10
10
Liftmaster
Rolling Code
BillionCode
390 MHz
11
Liftmaster 433.92
MHz
12
Liftmaster
Rolling Code 868.3 MHz
13
Marantec 433.92
MHz
14
NICE FLORS 433.92
MHz
15
Prastel 433.92
MHz
16
Somfy 433.42
MHz
17
Sommer 433.4 MHz
CHAMELEON R+A: ROLLER SHUTTERS, DOORS AND AWNINGS
11
18
Sommer
868.81
MHz
19
Universal
Fixed Code
Código Fijo
433.92
MHz Fixed Code
20
Universal
Rolling Code
Rolling Code
433.92
MHz Rolling Code
21
Universal
Rolling Code
868.3 MHz Rolling Code
22
Universal
Fixed Code
Código Fijo
300 MHz Fixed Code
23
Universal
Fixed Code
Código Fijo
310 MHz Fixed Code
24
Universal
Fixed Code 315 MHz Fixed Code
25
Universal
Fixed Code 318 MHz Fixed Code
CHAMELEON R+A: ROLLER SHUTTERS, DOORS AND AWNINGS
12
26
Universal
Fixed Code 330 MHz Fixed Code
27
Universal
Fixed Code 390 MHz Fixed Code
28
Universal
Roling Code
Open Code
315 MHz Rolling Code
29
Universal
Rolling
Open Code
318 MHz Rolling Code
30
V2 433.92
MHz
31
V2 315 MHz
32
V2 390 MHz
CHAMELEON R+A: ROLLER SHUTTERS, DOORS AND AWNINGS
13
33
DITEC 433.92
MHz
34
DITEC 315 MHz
35
DITEC 390 MHz
36
Aprimatic 433.92
MHz
37
Aprimatic 868.3 MHz
FSK
38
JCM TECH
868.3 MHz
39
JCM GO 868.3 MHz