explotacion exposicion
-
Upload
alexsandro-cossio -
Category
Documents
-
view
217 -
download
0
Transcript of explotacion exposicion
-
7/28/2019 explotacion exposicion
1/5
4.2 HOMOGENEOUS RESERVOIR MODEL- SLIGHTLY COMPRESSIBLE LIQUIDS
The basic of well-test analysis techniques for homogeneous-acting reservoir is the line-source (Ei-
funtion) solution to the diffusivity equation.
The relationship between bottomhole flowing pressure (BHFP), Pwf and the formation and well
characteristics for a well producing a slightly compressible liquid at a constant rate is
4.1
If we change from natural logarithms to base 10 logarithms and simplify, we can rewrite Eq. 4.1 in
a more familiar form,
..(4.2)
Where the skin factor,s, is used to quantify either formation or stimulation. Skin affects are
discussed later.
4.2.1 ANALYSIS OF CONSTANT-RATE FLOW TESTS
Eq. 4.2 describes the variation of the wellbore pressure with time when a well is produced at
constant rate. Production at a constant rate can be considered a pressure-drawdown or-flow test.
Comparing Eq. 4.2 whit the equation of a straight line, y=mx+b, suggests an analysis technique in
which the following term are analogous:
-
7/28/2019 explotacion exposicion
2/5
(4.3)
These analogies indicate that a plot of Pwf Vs. log t will exhibit a straight line from whitch the
slope, m, allows us to estimate k and s. fig. 4.1 is an example semilog graph of constant-rate flow
test date. The slope of the line, m, is the difference between the pressure, Pwf and Pwf,, one log
cycle apart, or m=Pwf,-Pwf,.
For single-phase flow, the formation permeability in the drainage area of the well is computed
from
Where the absolute value of m is used rearranging Eq.4.2 and combining with Eq. 4.3 gives. For
convenience, we set the time, t, equal to 1hour, and use the symbol P1hr for the BHFP AT THIS
TIME. NOTE THAT p1HR necessarily lies on the semilog straight line substituting these into Eq. 4.4
yields
In summary, from the straight line predicted by theory for a plot of constant-rate flow test data on
semilog graph paper, we can estimate k and s.
-
7/28/2019 explotacion exposicion
3/5
4.2.2 ANALYSIS OF PRESSURE-BUILDUP TESTS
AN EQUATION MODELING A PRESSURE-BUILDUP TEST CAN BE developed by use of superposition
in time. In term of the line sourcesolution given by Eq. 4.2, the bottomhole pressure (BHP) for the
rate history shown in fig. 4.2 is
Where
= shut-in BHP,
= DURATION OF THE CONSTANT-RATE PRODUCTION PERIOD BEFORE SHUT-IN, AND
= DURATION OF THE SHUT-IN PERIOD
IF WE COMBINE TERM AND SIMPLIFY, Eq 4.6 can be rewrite as
Comparing eq. 4.7 to the equation of straight line, y=mx+b, gives
-
7/28/2019 explotacion exposicion
4/5
This suggests that a plot of shut-it BHP, Pws from a buildup test as a function of the log of the
horner time ratio function,(tp+t)/ t, will exhibit a straight line with slope m.
The slope is the difference between two values of pressure, Pws+1 and Pws, 2 one log cycle apart.
To calculate permeability, we use the absolute value of the slope, or
From the semilog, the original reservoir pressure, Pi, is estimated by extrapolating the straight line
to infinite shut-in time where fig.4.3 illustrates calculation of the slope and
original reservoir pressure.
We also can solve for the skin factor, s, from a pressure-buildup test. At the instant a well is shut-
in, the BHFP IS
COMBINING Eqs. 4.7.4., and 4.9, we can derive an expression for the skin factor
-
7/28/2019 explotacion exposicion
5/5
where m=slope of the semilog straight line. Setting t= I hour, introducing the symbol P1hr for
Pws at t=1 hour on the semilog line, and neglecting the term log gives
Where at the instant of shut-in.in summary, using information obtained from a plot
of Pws vs log we can estimate k,pPb and s
En espaol