Respiro Meter 1
Transcript of Respiro Meter 1
-
7/31/2019 Respiro Meter 1
1/14
UNIVERSITI TEKNOLOGI MARA
INTERNATIONAL EDUCATION COLLEGE
(INTEC)
NAME :HANNAH CHEN YEE SZE
GROUP :12M12
STUDENT ID :2011219506
TITLE OF PRACTICAL :MEASURING THE RATE OF OXYGEN UPTAKE USING A
RESPIROMETER
DATE :3/10/2012
LECTURER :MS FATHIAH
Introduction:
-
7/31/2019 Respiro Meter 1
2/14
Living organisms require energy for various activities and living processes. Some of the
processes which require energy are excretion of waste products, muscle contraction which enables
locomotion, cell division in which new cells are produced for growth and development,
transmission of nerve impulses, absorption of digested food through active transport, active
transport of biochemical substances, maintaining the body temperature in warm-blooded animals)
and synthesis of lipids, hormones, proteins and enzymes. Organic substances like carbohydrates,
lipids and proteins contain chemical energy which enters living organisms in the form of food and
in order to be converted into a form of energy which can be readily used by cells, respiration is
carried out. There are two types of respiration- aerobic respiration and anaerobic respiration.
Aerobic respiration takes place in the cells of living organisms to convert chemical energy
from food into energy in the form of ATP. It is a redox reaction and its equation is as shown
below.
C6H12O6 + O2 CO2 + H2O + energy
The main substrate for respiration is glucose. When glucose is not available, amino acids
and fatty acids can be used as substrates too. There are many complicated steps involved in
respiration, which are all controlled by enzymes. The first stage of respiration is glycolysis. In
this process, the 6-carbon glucose is phosphorylated by using two molecules of ATP. This
activates the glucose and prevents glucose from being transported across the cell membrane. Then,
the phosphorylated 6-carbon molecules will then be split into two carbon triose phosphate called
glyceraldehyde-3-phosphate. Each molecule of triose phosphate will be oxidised by nicotiamide
adenine dinucleotide (NAD). Two molecules of ATP are also produced. This production of ATP
is known as substrate level phosphorylation. Each molecule of triose phosphate will result in a
pyruvate. The net gain of ATP from glycolysis is two molecules.
-
7/31/2019 Respiro Meter 1
3/14
Diagram 1: Glycolysis
Next, the pyruvate will enter the link reaction and this process requires oxygen. Pyruvate
is decarboxylated to form a molecule of carbon dioxide. It is also dehydrogenated to form a
molecule of reduced NAD. Pyruvate becomes acetate which combines with coenzyme A to form
acetyl coenzyme A (acetyl coA). This will proceed to the Krebs Cycle, which is also known as the
citric acid cycle.
-
7/31/2019 Respiro Meter 1
4/14
Diagram 2: Link Reaction and Krebs Cycle
Acetyl coA will combine with a four-carbon molecule called oxaloacetate to form citrate, a
six-carbon molecule. Coenzyme A will then be released and recycled in the next link reaction.
Citrate is decarboxylated and dehydrogenated, forming one molecule of carbon dioxide and one
molecule of reduced NAD. It will form a five-carbon molecule known as alpha-ketoglutarate.
dephosphorylated, decarboxylated, and then undergo three times of dehydrogenation to form one
molecule of ATP, one molecule of carbon dioxide, two molecules of reduced NAD and one
molecule of reduced flavine adenine dinucleotide (FAD). Alpha-ketoglutarate itself becomes
oxaloacetate which combines with acetyl coA. This forms a cycle, hence the name Krebs cycle.
The hydrogen acceptors (reduced NAD and reduced FAD) will enter the electron transport
chain (ETC) to be oxidised. As the electrons pass from carriers to carriers, energy is released in
the form of ATP
-
7/31/2019 Respiro Meter 1
5/14
Diagram 3: Electron Transport Chain
In the chemiosmotic theory by Peter Mitchell, he said that protons were actively
transported into the intermembrane space using energy provided by the electrons as electrons are
passed down the electron transport chain. The protons cannot diffuse the inner membranes as they
are impermeable to protons. The pH gradient , concentration gradient and electrochemical gradientthat exist between the intermembrane space and the matrix of the mitochondria causes the protons
to move back into the matrix via special pores found on stalked particles. The ATP-ase on these
pores are used to drive the synthesis of ATP and 38 ATP are gained.
Anaerobic respiration is carried out when oxygen is absent. In plants, this is known as
alcoholic fermentation, where else in animals, it is known as lactic acid fermentation. Glycolysis
is still carried out, but pyruvate will not enter the link reaction but undergo anaerobic respiration.
The product is lactic acid and only two molecules of ATP. No carbon dioxide is produced. It ismuch less efficient compared to aerobic respiration because only two molecules of ATP are
formed in contrast to the 38 molecules of ATP formed by aerobic respiration. This shows that
oxygen is very important as the final electron acceptor which allows the Krebs cycle and electron
transport chain to work.
-
7/31/2019 Respiro Meter 1
6/14
Yeasts are eukaryotic microorganisms from the kingdom Fungi. They are unicellular and
their size varies depending on the species, usually ranging between 3-4m in diameter. They
usually reproduce asexually by a process called budding. Yeasts are chemoorganotrophs, as they
use organic compounds as a source of energy and do not require sunlight to grow. They are also
facultative anaerobes, which means they can respire both aerobically and anaerobically.
Diagram 4: Yeast
-
7/31/2019 Respiro Meter 1
7/14
Objective:
To investigate the rate of oxygen uptake of yeast using a respirometer.
Problem Statement:
What is the rate of oxygen uptake of yeast?
Hypothesis:
The respiration rate can be measured by the means of a respirometer by calculating the uptake of
oxygen per unit time.
Null hypothesis:
The respiration rate cannot be measured by the means of a respirometer by calculating the uptake
of oxygen per unit time.
Apparatus:
Boiling tubes, 1cm3 syringe, three-way tap, manometer tube, gauze, measuring cylinder, stopper,
delivery tubes, micropipette
Materials:
Yeast, red dye, filter paper, potassium hydroxide solution, cling film
-
7/31/2019 Respiro Meter 1
8/14
Procedure:
Diagram 5: Apparatus Set-up
1. The apparatus was set up as shown above
2. Both of the boiling tubes were filled with 7cm3 of potassium hydroxide solution.
3. One of the boiling tubes was stoppered, and a syringe was inserted on top of the stopper, as
shown in Figure .
4. A gauze was placed in the other boiling tube.
5. Two filter papers soaked in yeast were placed in the experimental tube, on the gauze and
not touching the potassium hydroxide solution.
6. The stoppers were replaced.
7. The manometer tube was filled with approximately 200 l of red dye using a micropipette.
-
7/31/2019 Respiro Meter 1
9/14
8. The manometer tube was connected to both of the boiling tubes simultaneously.
9. The liquid in the manometer tube was adjusted using the syringe attached to the non-
experimental tube so that the level of the liquid in the manometer tube became equal
10. The starting position of the fluid was recorded
11. The three way tap was turned to ensure air flows between the manometer and the boiling
tubes
12. The readings of the level of the coloured dye is recorded every minute for 6 minutes.
The increment of red dye level was assumed to be the volume of oxygen absorbed
by the yeast.
Results:
Initial level of manometer fluid = 2.5cm
Initial position of syringe piston = 0.5cm3
Displacement in manometer level (cm) = Final reading (cm) Initial reading (cm)
*Displacement in manometer level corresponds to the total amount of oxygen consumed.
Time/Minutes Readings on Manometer/cm Displacement inManometer Level/cm
0 2.5 0.00
1 2.6 0.10
2 3.1 0.60
3 3.4 0.90
4 3.8 1.30
5 4.4 1.90
6 4.5 2.00
7 4.7 2.20
8 5.0 2.50
9 5.3 2.80
10 5.6 3.10
11 5.8 3.30
12 6.1 3.60
Table 1: Table showing Displacement of manometer Level in a Period of 12 Minutes
Final level of manometer fluid = 6.1cm
-
7/31/2019 Respiro Meter 1
10/14
Final position of syringe piston = 0.5cm3
Total increment in manometer reading = Total amount of oxygen consumed (cm)
= 6.1 cm 2.5 cm = 3.6 cm
Calculated rate of oxygen uptake (cm s-1) =
= 3.6 cm 720 seconds
= 5.00 x 10-3 cm s-1
-
7/31/2019 Respiro Meter 1
11/14
Analysis of results:
In this experiment, yeast was used as it is cheap, easily available and also easy and safe to
handle. Before the experiment, the level of the red dye in the manometer was adjusted to be at the
same level at both sides and the initial level on the experimental tube side was recorded.
When the three way tap is turned to the direction of the manometer and the stopwatch was
started, it can be seen that the level of red dye at the side of the manometer connected to the
experimental tube started increasing, while the level of dye on the control side decreased. This
shows that the volume of air in the experimental tube is decreasing as time passes. As the volume
of air decreases, the pressure also decreases. Thus, the level of red dye increases in response to the
decreased pressure. The volume of air decreased as carbon dioxide released during respiration has
been absorbed by the potassium hydroxide solution, while the oxygen in the experimental tube is
being used up in respiration. As there is no respiration taking place in the control tube, the volume
of gas remains constant and the pressure is constant as well.
The control tube is very important as it helps to compensate for the change in temperature
and pressure of the atmosphere. This will help to ensure that the change in level of red dye is
solely due to the respiration of yeast and not by other external factors.
The rate of respiration is calculated by measuring the amount of oxygen consumed by yeast
over a period of time. The oxygen consumed is indicated by the level of fluid in manometer. The
equation for respiration is as shown below:
-
7/31/2019 Respiro Meter 1
12/14
Discussion:
The main limitation in this experiment is that yeast is a facultative anaerobe and can respire
both aerobically and anaerobically. Thus, the rate of respiration calculated may not be accurate as
when yeast respires anaerobically, they do not take in oxygen and the carbon dioxide released is
absorbed by potassium hydroxide solution. Thus, there is no change in volume of gas in the
experimental tube and hence, no change in pressure. The level of red dye does not change.
Fluctuations in surrounding temperature also affect the experimental results as gas expands
when temperature increases and thus have a bigger volume. Although this may be compensated
slightly by the control set, it may still affect the displacement of the red dye over the period of time
when it is recorded.
The connections to the tubes may not have been completely tight and secure, for example
the connection between the delivery tubes to the manometer tube, the stopper for the boiling tubes
and the connection between the syringe and the non-experimental tube. This may allow the gas
inside the tubes to escape through the unsealed gaps.
Besides, parallax error are likely to occur when the measurement of the level of the
coloured liquid in respirometer. This will result in wrong readings being taken and the results ofthe experiment being less accurate.
Some ways to overcome these limitations and sources of errors are to use other organisms
such as crickets that only undergo aerobic respiration.
Fluctuations in the surrounding temperature can be overcome by using a water bath set at a
constant temperature. This will ensure temperature is kept constant and does not affect the
displacement of red dye, thus making the results of the experiment more reliable.
All the connections should be sealed tightly with cling film to ensure the connections are
airtight and air is unable to escape via the connections. This will ensure that the air pressure does
not change due to gas escaping from the tubes.
-
7/31/2019 Respiro Meter 1
13/14
When readings are taken, the eye level must be perpendicular to the scale of the
respirometer. This will prevent parallax error and wrong readings to be taken and make sure the
results are more accurate and reliable.
Safety precautions:
1. Care must be taken when handling the apparatus to avoid the apparatus from breaking. If
the apparatus breaks, the broken apparatus should be swept away using a broom, not
using a hand as the broken glass may cut the fingers.
2. Potassium hydroxide solution has to be handled with care as it is strong base and corrosive.
3. If the KOH comes into contact with skin accidentally, wash under running tap water
immediately.
Conclusion:
During aerobic respiration where oxygen is available, living organisms take in oxygen from the
surrounding and release carbon dioxide. The respiration rate can be measured by means of a
respirometer by calculating the uptake of oxygen per unit time. The displacement of the coloured
fluid in the capillary tube is an indication to the uptake of oxygen. In this experiment, we can
conclude that the rates of respiration of yeast is 5.00 x 10 -3 cm s-1
Further work:
For further investigation, a manipulated variable can be included to this experiment, for instance,
the surrounding temperature. Water bath with different temperature can be used and their effects
on the respiration rate can be investigated. Theoretically, the rate of respiration increases with
temperature as the enzyme activity speeds up at higher temperature. However, if the temperature is
too high, enzymes may denature, and finally respiration ceases and organisms die.
Word count: 2240 words
-
7/31/2019 Respiro Meter 1
14/14
Bibliography:
Non web based:
1. Salters-Nuffield Advanced Biology for Edexcel A2 Biology
2. Clegg C.J, Edexcel Biology, Hodder Education, London, UK, 2008, A Pearson Company.
3. Edexcel A2 Biology, A Pearson Company 2008.
Web based:
1. http://www.purchon.com/biology/respire.htm
2. http://biology.about.com/od/cellularprocesses/a/cellrespiration.htm l
3. http://users.rcn.com/jkimball.ma.ultranet/BiologyPages/C/CellularRespiration.html
4. http://www.essortment.com/all/cellularrespira_rmpr.htm
5. http://www.wisegeek.com/what-is-aerobic-respiration.htm
6. http://idv.sinica.edu.tw/ckao/About%20the%20Lab.html
http://www.purchon.com/biology/respire.htmhttp://biology.about.com/od/cellularprocesses/a/cellrespiration.htmlhttp://users.rcn.com/jkimball.ma.ultranet/BiologyPages/C/CellularRespiration.htmlhttp://www.essortment.com/all/cellularrespira_rmpr.htmhttp://www.wisegeek.com/what-is-aerobic-respiration.htmhttp://www.purchon.com/biology/respire.htmhttp://biology.about.com/od/cellularprocesses/a/cellrespiration.htmlhttp://users.rcn.com/jkimball.ma.ultranet/BiologyPages/C/CellularRespiration.htmlhttp://www.essortment.com/all/cellularrespira_rmpr.htmhttp://www.wisegeek.com/what-is-aerobic-respiration.htm