1 32 4 5
NEWPROG
6 7
1 32 4 5
NEWPROG
6 7
C11 32 4 5
NEWPROG
6 7
C1
LN
L N
LN
MENU OK
+
1L
2N
MENU OK
+
1200 W
60 VA
2300 VA
60 W 7µF
+
c
R
1800 W
+
1800 W
2300 W
+
3680 W
! Indicaciones para la seguridadEste producto debiera ser instalado preferentemente por un técnico electricista capacitado, en caso contrario existe peligro de incendio o de una descarga eléctrica. Antes de proceder a la instalación, es imprescindible haber leído y entendido las instrucciones para el servicio, asimismo se tiene que tener en cuenta y examinar el lugar de montaje específico para el producto y que solamente se deben utilizar accesorios originales. Todos los productos de Legrand sólo deben ser abiertos y reparados por colaboradores de la empresa Legrand que dispongan de la formación especial correspondiente. Si el producto es abierto o reparado por personal no autorizado por la casa Legrand, se pierden en consecuencia todos los derechos de responsabilidad civil, así como de repuesto y de garantía. Utilizar exclusivamente los accesorios de la marca Legrand. El aparato contiene una pila botón no recargable de CR2032. Una vez agotada la vida útil del producto, ésta debe extraerse correctamente y desecharse de acuerdo con las disposiciones legales de cada país y teniendo en cuenta las normas de protección del medio ambiente.
! Safety notesThis product may be installed only by a qualified electrician. Non-compliance may result in a fire hazard or electric shocks. Before installation, read the operating instructions and observe the product-specific requirements for the installation location. Use only original spare parts for repair and maintenance. All Legrand products may be opened and repaired only by specially trained Legrand personnel. Unauthorised opening and repair by other persons will invalidate all claims for liability, replacement or warranty services. The device contains a Li cell type battery (Li) CR2032. When the product reaches the end of its life, this cell must be correctly removed and disposed of in accordance with nati-onal legislation and the requirements of environmental protection.
• Confirmación de la selección o incorporaciónde los parámetros
• Confirm menu selection or adopt parameters
• Selección de los puntos de menú o ajustede los parámetros. Selección del canal.
• Select menu items or set parameters. Channel selection
• Selección de menú, Atrás en el menú,Activación > 1 s = indicación de servicio
• Menu selection, back in menu, actuation > 1s = back to status display
• El dispositivo no puede conectar la protección de bajo voltaje.
• The device should not be used on isolated low voltage.
b
HORA/DATA VE IVSET
SET VE IV SET
DIA
IV
IVSET
DIA
IV SET IV
MES
SET IV
MES
SET IV
ANO
SET VE IVSET VE IV
SET VE IV
SET
DIA
VE SET
DIA
VE SET VE
MES
SET VE
MES
SET VE
ANO
VE
• Horario de verano• Summertime
• Hora de inverno• Wintertime
HORA/DATA VE IVSETHORA/DATA VE IV
PROGMODO
SET
HORA/DATA VE IVSET
• Regular a hora/data• SET TIME/DATE
a HORA/DATA VE IVPROGMODO
SET HORA/DATA VE IVSET HORASET HORASET HORASET HORASET
1 32 4 5ON
OFF
NOVPROG
C1
1 32 4 5ON
OFF6 7
NOVPROG
C1
TESTMODIFNEWPROG
C1
TESTMODIFNOVPROG
C 2
C1
C2
TESTMODIFNOVPROG
C1
NOVPROG
C1
TESTMODIFNOVPROGMODO
SETHORA/DATA VE IVPROGMODO
SET
C1 C2
DAY1 - 7 1 - 5 6 - 7 1 32 4 5
ON
OFF6 7 1 32 4 5
ON
OFF6 7 1 32 4 5
ON
OFF6 7
5x
ANY DAY
• Selección de día de conexión 2 • Select switch-on day 2
NOVPROG
C1
1 32 4 5ON
OFF
NOVPROG
C11 32 4 5ON
OFF6 7 1 32 4 5
ON
OFF6 7
• Selección de día de desconexión 2 • Select switch-off day 2
TESTMODIFNOVPROG
C1
SET
DIA
DATA SET DATA
DIA
SET DATA
MES
SET DATA
MES
SET DATA
ANO
SET DATA
ANO
HORA/DATA VE IVSET
• Programación• Prog New
1 32 4 5 6 7
NOVPROG
C1
• Modo de acción: tipo 1.B. S. T. IEC/EN 60730-1, IEC/EN 60730-2-7 Funcionamiento en entorno convencional Montage: Montaje en cuadro de distribución Grado de suciedad: 2 Salida de conmutación sin tensión
• Operating principle: Typ 1.B. S. T. IEC/EN 60730-1, IEC/EN 60730-2-7 Operation in a normal environment Montage: in distribution panel, Degree of contamination: 2 Switch output, potential-free
NT
2925
60/0
0
• ProgramaciónUn programa = hora de conexión + hora de desconexión + días de conexión y días de desconexión Programas con días de conexión / desconexión predefinidos • DIA 1 – 7 (LU – DO) • DIA 1 – 5 (LU – VIER) • DIA 6 – 7 (SA y DO) Los programas de un canal disponen entre sí de un enlace lógico O (OR).
• ProgrammingOne program = switch-on time + switch-off time + switch-on and switch-off days Programs with predefined switch-on / switch-off days • DAY 1-7 (MO-SU) • DAY 1-5 (MO-FR) • DAY 6-7 (SA and SU) Programs for each channel are interlinked with OR logic.
• Programas: 28 14 / canal• Programs: 28 14 / channel
• Precisión del reloj: ± 1 s / día dadas las condiciones típicas de instalacíon• Clock accuracy: ± 1 s / day under typical installation conditions
230V 50/60Hz
1x 16A/250V~µ cos ϕ = 1 2x 16A/250V~µ cos ϕ = 1
0,9 W 1,3 W
M
1 ... 4 mm2 0,5 ... 2,5 mm2
230V 50/60Hz
6 037 72 6 037 73
• Consumo de potencia efectiva• Power cons.:
• Reserva de cuerda: 3 años• Battery reserve: 3 years
MicroRex D21/D22 Plus2
6 037 72 / 73
• Interruptor horario• Time switch
+-
+-
- 20 °C … +55 °C
- 20 °C … +60 °C
IP 20
C1
C2
MODIFPROG
C1
• Reposição• Reset
• ¡Nota! La memoria se borra y todos los datos ajustados se pierden. Accionar todas las teclas a la vez durante aprox. 2 segundos y soltarlas.La hora, la fecha, el horario de verano / invierno y las horas de conmutación se tienen que volver a ajustar.
• Note!A reset clears the entire memory, which means that all previously set data will be lost. Press and hold all four keys together for about 2 seconds, then release them. The time, date, summertime/wintertime and switching times will have to be re-entered.
1 32 4 5 6 7
C1C2
• El dispositivo no puede conectar la protección de bajo voltaje.
• The device should not be used on isolated low voltage.
HORA/DATA VE IVPROGMODO
SETTESTMODIFNOVPROG
MODO
SET
TESTMODIFNEWPROG
C1
TESTMODIFNOVPROG
C 2
C1
C2
MODIFPROG
C1
MODIFPROG
C1
1 32 4 5
MODIF
ON
OFF
PROG
C1
6 7
1 32 4 5
MODIF
ON
OFF
PROG
C1
6 71 32 4 5
MODIF
ON
OFF
PROG
C1
6 7 1 32 4 5
MODIF
ON
OFF
PROG
C1
6 7
TESTMODIFNOVPROG
C1
TESTMODIFNOVPROG
C1
d
C1 C2
• • •
• Modificación de programa• Edit program
• Modificación de horas deconmutación
• Change switching times
• Modificación de díasde conmutación
• Change switching days
MODIFPROG
C1
Prog 1 Prog 2 Prog 3
• • • •
NOVPROG
C1
1 32 4 5
MODIF
ON
OFF
PROG
C1
6 7
1 32 4 5ON
OFF6 7 1 32 4 5
ON
OFF6 7
1 32 4 5ON
OFF6 7 1 32 4 5
ON
OFF6 7
1 32 4 5ON
OFF6 7
5x
• DEL ONE -> Borrar programa individual, DEL C1/2 -> Borrar programas de un canal• DEL ONE -> Delete a single program, DEL C1/2 -> Delete the programs for a channel
TESTMODIFNOVPROG
C1
MODIFPROG
C1
MODIFPROG
C1
MODIFPROG
C1
1 32 4 5
MODIF
ON
OFF
PROG
C1
6 7
MODIFPROG
MODIFPROG
C1
MODIFPROG
Prog 2
• • •
MODIFPROG
C1
Prog 3
• • •
e
TESTMODIFNOVPROG
C1
TESTPROG
C1
PROG
C1
TEST
TESTPROG
C1
1 32 4 5
TEST
ON
OFF
PROG
C1
6 7 1 32 4 5
TEST
ON
OFF
PROG
C1
6 7
1 32 4 5
TEST
ON
OFF
PROG
C1
6 7
TESTPROG
• • •
• • •
PROG
C1
TEST
• • •
Prog 1 Prog 2
DAY 1 DAY 2
• prog -> Programas en el orden de la entrada SERIAL -> Ordenes de mando en orden cronológico• prog -> Programs in the order entered SERIAL -> Switching commands in chronological order
• Modo PERManent • Mode PERManent
• Conmutación Marcha / Paro permanente• Continuous switching On/Offf
C1AUTO
C 2
PERMMODEC1
C2
EXTRA
AUTO PERMMODO EXTRA
HORA/DATA VE IVPROGMODO
SET
AUTO EXTRAPERMPROGMODO
SET
AUTO EXTRAPERMMODOC1
AUTO EXTRAPERMMODOC1
1 32 4 5
HORA
C1 ONPERM
SUPERM
6 7
1 32 4 5
HORA
C1 OFFPERM
SUPERM
6 7
PERMMODOC1
PERMMODOC1
C1 C2
• Modo EXTRA• Mode EXTRAg
C1AUTO
C 2
PERMMODEC1
C2
EXTRA
AUTO PERMMODO EXTRA
1 32 4 5ON
HORA
C1 OFF
6 7
EXTRA
SU
PROX
EXTRAHORA/DATA VE IV
PROGMODO
SET
AUTO EXTRAPERMPROGMODO
SET
AUTO EXTRAPERMMODOC1
AUTO EXTRAPERMMODOC1
C1 C2
• El estado de conmutación prescrito por el programa se invierte. Al activarse la orden de conmutación siguiente, el interruptor horariovuelve a la función de cierre de circuito / apertura de circuito, automática.
• State of contact set by program will be reversed. The next program automatically returns the switch to ON or OFF as programmed.
MODIFPROG
• Modificación de programa• Prog MODIFY
• Prog MODIF• Prog MODIFY
+
• Antes de desmontar el módulo hay que desconectar el aparato.Conectar la tensión del aparato sólo después de haber montado otra vez el módulo. Emplear exclusivamente pilas de litio de tipo botón (LiMnO2) CR2032, 3V, tipo de alta temperatura mín. +70°C.
• Switch off the device before dismantling the module. Do not switch on again until the module has been installed. Always use a Li cell type battery (Li) CR2032, 3V. High temperature type min +70°C.The time, date, summertime/wintertime and switching times will have to be re-entered.
• Prog TEST• Prog TEST