7/25/2019 Instructivo HOBO H 21 01
1/52
Part #: MAN-H21Doc #: 6106-J
HOBO
Weather Station
Users Guide
7/25/2019 Instructivo HOBO H 21 01
2/52
ii HOBO Weather Station Users Guide
Contact Information
For support, please contact the company that you bought the product from: Onset Computer Corporation or an
Onset Authorized Dealer.
Onset Computer Corporation
470 MacArthur Blvd.
Bourne, MA 02532Mailing Address:
P.O. Box 3450
Pocasset, MA 02559-3450
Phone: 1-800-LOGGERS (1-800-564-4377) or 508-759-9500
Fax: 508-759-9100
Customer Service Hours: 8AM to 5PM Eastern Time
Technical Support Hours: 8AM to 8PM Eastern Time
Email: [email protected]
Main Onset Web site: www.onsetcomp.com
FTP site: ftp.onsetcomp.com
If you purchased the products through an Onset Authorized Dealer, you can also refer to www.hobohelp.com for
support information.
Safety Information Read first
WARNING: Severe shock hazard. Before installing weather station tripod or mounting poles,
ensure that there are no electrical power lines overhead. Do not install the system during any
atmospheric electrical activity. Do not assemble or transport tripods, mounting poles, or other
structures unless there is sufficient clearance from potential electrical sources or other
obstructions.
WARNING: Do not climb on or around the weather station tripod. The weather station and any
of its associated hardware, towers, poles, etc. are not designed to support the weight of a person.
Injury may result.
WARNING: If using stakes to stabilize the tower, ensure that there are no underground wires or
pipes under the weather station.
WARNING: Fire, Explosion, and Severe Burn Hazard. The logger may contain a lithium battery.
The battery may explode if the logger is exposed to extreme heat or conditions that could damage
or destroy the battery case. Do not attempt to recharge or heat the logger or battery above +185F
(+85C). Do not dispose of the logger or battery in fire. Do not expose the contents of the battery
to water. Dispose of the battery according to local regulations for lithium batteries.
WARNING: Do not use weather station as part of a critical control system. This system is not
intended to be a fail-safe mechanism for anticipating life-threatening conditions, such as flash
floods.
2009-2011 Onset Computer Corporation, all rights reserved.
Printed in USA.
Onset and HOBO are registered trademarks of the Onset Computer Corporation. Other products and brand names
may be trademarks or registered trademarks of their respective owners.
7/25/2019 Instructivo HOBO H 21 01
3/52
HOBO Weather Station Users Guide iii
Table of Contents
Section 1: Introduction .............................................................................. 5
How to Use this Manual ........................................................................................................................ 5
Specifications ........................................................................................................................................ 6
Logger components .............................................................................................................................. 7
Status Lights .................................................................................................................................... 8
Section 2: Setup and Test ......................................................................... 9
Items Required ...................................................................................................................................... 9
Steps ................................................................................................................................................... 10
Communicating with the Logger.......................................................................................................... 11
Launching the Logger ......................................................................................................................... 11
Reading out Data ................................................................................................................................ 12
Batteries .............................................................................................................................................. 13
Estimating Battery Life ................................................................................................................... 14Additional guidelines: ..................................................................................................................... 14Using a 9-Volt Battery .................................................................................................................... 15Using a 9-Volt Battery Eliminator ................................................................................................... 15
Adding and Removing Sensors........................................................................................................... 16
Section 3: Field Setup ............................................................................. 17
Guidelines for Typical Field Setup ...................................................................................................... 18
Site Selection ................................................................................................................................. 18Mounting ........................................................................................................................................ 19Installing Sensors ........................................................................................................................... 19
Field Preparation Checklist ................................................................................................................. 20
Tasks for Setting up the Tri-pod .......................................................................................................... 23
Task 1: Assemble Tripod ............................................................................................................... 24Task 2: Install Grounding Kit .......................................................................................................... 31Task 3: Temporarily Install Upper Mast (Optional) ........................................................................ 32Task 4: Mount Cross Arm (Optional) ............................................................................................. 33 Task 5: Mount Upper Mast to Lower Mast ..................................................................................... 34 Task 6: Mount Logger to Upper Mast ............................................................................................ 35Task 7: Install Guy Wire Kit (Optional) ........................................................................................... 36
Task 8: Position and Level Sensors .............................................................................................. 38 Task 9: Final Setup ........................................................................................................................ 38
7/25/2019 Instructivo HOBO H 21 01
4/52
iv HOBO Weather Station Users Guide
Section 4: Maintenance ........................................................................... 41
General Maintenance .......................................................................................................................... 41
Performing a visual inspection ............................................................................................................ 41
Batteries .............................................................................................................................................. 42Checking Battery Status ................................................................................................................ 42Changing Batteries ........................................................................................................................ 42
Cleaning the Weather Station ............................................................................................................. 43
Verifying Sensor Accuracy .................................................................................................................. 43
Section 5: Reference ............................................................................... 45
Memory ............................................................................................................................................... 45
Time Accuracy ..................................................................................................................................... 47
Resetting the Clock ............................................................................................................................. 48
Section 6: Troubleshooting .................................................................... 49
7/25/2019 Instructivo HOBO H 21 01
5/52
Section 2: Setup and Test
HOBO Weather Station Users Guide 5
Section : Introduction
The HOBOWeather Station is a data logger designed for
multi-channel climate monitoring. The Weather Stationrepresents the next generation of data logging because it
uses a network of smart sensors for taking measurements.
Key features of the smart sensors include:
Automatic detection. No extensive programming,wiring, or calibrating is required to set up sensors.
Easy expansion. Because the logger is not pre-configured, up to 15 sensor parameters of any type
or combination can be added simply by plugging
them in before logging begins.
Digital network. The connections between thesmart sensors and the logger are digital, ensuring
accurate, reliable data collection and storage.
How to Use this ManualThis manual walks you through the steps of setting up, operating, and maintaining the HOBO Weather
Station. Use this manual to learn how to:
Setup the logger and perform an initial test
Deploy the Weather Station in the field
Troubleshoot problems
Maintain the Weather Station
It is important that you setup and test your logger using the steps in Section 2 before continuing with
deploying the Weather Station on site.
For your convenience, this manual includes three section dividers to organize sensor manuals and
hardware packing lists. It is recommended that you add all sensor manuals and hardware packing lists to
this binder.
7/25/2019 Instructivo HOBO H 21 01
6/52
Section 2: Setup and Test
6 HOBO Weather Station Users Guide
Specifications
HOBO Weather Station
Operating Range -20 to 50C (-4 to 122F) with alkaline batteries,-40 to 70C (-40 to 158F) with lithium batteries
Sensor Inputs 10, expandable to 15 with optional adapters
Data Channels Maximum of 15 (some sensors use more than one data channel; seesensor manual for details)
Communication 3.5 mm serial port or weatherproof external connector
Dimensions 23 cm H x 10 cm D x 18 cm W (9 x 4 x 7 inches)
Weight 0.9 kg (2 lbs)
Memory 512K nonvolatile flash data storage
Memory Modes Stop when full, wrap around when full
Operational Indicators Seven status lights provide logging and sensor network status
Logging Interval 1 second to 18 hours, user-specified interval
Battery Life 1 year typical use (up to 10 sensors with 10 minutes or longer logginginterval)
Battery Type Four standard AA alkaline batteries included (for operating conditions -20 to 50C [-4 to 122F]); optional AA lithium batteries available foroperating conditions of -40 to 70C (-40 to 158F)
Time Accuracy 0 to 2 seconds for the first data point and 5 seconds per week at 25C(77F)
Data Type Supports measurement averaging based on availability of supportingdata from sensor
Logger Start Modes Immediate, push-button, or delayed start options
Data Communication Current reading while logging, offload while logging, or offload whenstopped
Environmental Rating Weatherproof
Mounting Mast (3.8 cm [1.5 inches] maximum diameter) or wall mount
Enclosure Access Hinged door secured by four screws
Sensor Network CableLength
100 m (328 ft) maximum
Part Number H21-001
7/25/2019 Instructivo HOBO H 21 01
7/52
Section 2: Setup and Test
HOBO Weather Station Users Guide 7
Logger componentsThe following diagram explains the key parts of the Weather Station.
Figure 1: All logger components
Sensor connectionports, where up to 10smart sensors can be
plugged in. Use a sensoradapter (Part # S-ADAPT)to plug up to 15 sensors inthese ports
Status lights, see thetable in this section fordetails on each of theseven lights
Internal communications
portused for connecting tothe computer or U-Shuttle.
Start logging button; usethis button when the loggeris configured to launch withbutton start. Press and holduntil all lights flash
Battery door thumbscrews,unscrew these to removebattery door
Cable tie bracketuse tosecure the sensor cableswith a cable tie
Battery doorcoversfour AA batteries andauxiliary 9 Volt batteryport
External
communications portused for connecting to the
computer or U-Shuttle,allowing you to keep thelogger closed whilereading out, launching, orchecking status
7/25/2019 Instructivo HOBO H 21 01
8/52
Section 2: Setup and Test
8 HOBO Weather Station Users Guide
Status Lights
There are seven lights on the Weather Station that indicate logger activity and status. The following table
explains the function of these lights.
This light: Blinks when: Notes
Sensor Activity There is activity on the sensornetwork.
Network activity is defined as communicationfrom the logger to the sensor or vice versa.
Delay Start The logger has been configuredto launch with a delayed start; willcontinue blinking until the definedstart date/time.
The logger will not record measurementswhile this light is blinking. Sensors can beadded at this time.
Button Start The logger has been configuredto start with a button start; willcontinue blinking until you pressand hold the button on the loggerfor a couple of seconds.
The logger will not record measurementswhile this light is blinking. Sensors can beadded at this time.
OK Every two seconds while thelogger is recording data fromsensors.
Sensors cannotbe added at this time.
Bat Low The battery power is less than25% capacity.
The logger will continue to run. However, youshould read out the logger and then replacethe batteries soon.
Mem Low Less than 25% of memory isavailable for saving data.
The logger will continue to run until allmemory is used. This light will only blink if thelaunch parameter Wrap Around When Full isnot selected (see the Launchingsection onpage 11 for details on the Wrap Around WhenFull setting).
Error There is or has been a sensorcommunication failure.
If this light is blinking in conjunction with theOK light, there was a communication failure.The system has recovered, but you may havean intermittent problem.
If this is the only blinking light, then at leastone sensor is currently not communicating.Immediate investigation is recommended.
In general, it is recommended that you readout any data when this light is blinking,investigate the problem, and re-launch thelogger.
7/25/2019 Instructivo HOBO H 21 01
9/52
Section 2: Setup and Test
HOBO Weather Station Users Guide 9
Section 2: Setup and Test
Onset recommends that you setup and test the logger before deploying the Weather Station in the field.
Items RequiredTo setup the logger, you will need the following materials:
Flat head screwdriver
Four AA alkaline batteries (included with the logger) or four AA lithium batteries
One or more smart sensors
PC interface cable (Onset part number CABLE-PC-3.5)
Computer with logger software installed
7/25/2019 Instructivo HOBO H 21 01
10/52
Section 2: Setup and Test
10 HOBO Weather Station Users Guide
StepsComplete the following steps to setup your Weather Station.
1. Use a flat head screwdriver to loosen the four screws on the front cover of the logger. Open thelogger door.
2. Unscrew the two thumbscrews on the battery door cover and remove the battery door. Insert fourAA alkaline or lithium batteries, observing polarity. Once the batteries are installed correctly, the
status lights will blink for a second. See Batteries on page 13 for more details.
Figure 2: Logger components
3. Replace the battery door cover and thumbscrews.
4. Insert one or more sensors into the sensor ports. Refer to www.onsetcomp.com for a current listof available sensors. Onset recommends that you test all sensors you plan to deploy with the
logger.
Refer to the manuals provided with the sensors for sensor specifications, mounting information,
and recommended maintenance.
See Adding and Removing Sensors on page 16 for details.
5. Plug the PC interface cable into the internal communications port on the logger. SeeCommunicating with the Logger on page 11 for details.
6. Using the logger software, click the Launch icon. If the logger is not found, make sure the correctCOM port is selected. Refer to theHOBOware Users Manualfor details on changing the COM
port. See Launching the Logger on page 11 for details.
7. Make sure all the sensors connected to the logger are visible in the Launchscreen.
8. Choose a Logging Intervalof a few seconds so that your test will yield enough data to analyze.
Select the Start Logging Nowoption, and click the Startbutton to launch the logger. The
logging ok light on the logger should blink every two seconds during logging.
9. After a couple of minutes, click the Readout icon in the logger software to offload data from thelogger. You can choose to either stop the logger before reading it out, or let it continue logging
while reading out. See Reading out Data on page 12 for details.
10.Check the data and make sure it appears normal for all sensors.
Congratulations! You have now launched and offloaded the Weather Station. Proceed to Section 3: Field
Setup on page 17 for details on deploying the logger.
Battery doorthumbscrews
Status lights
Internal
communicationsport
7/25/2019 Instructivo HOBO H 21 01
11/52
Section 2: Setup and Test
HOBO Weather Station Users Guide 11
Communicating with the LoggerThe logger has both an internal and external communication port for connection with a computer or U-
Shuttle. See the Shuttle manual for information on using the logger with a U-Shuttle.
The internal port is located inside the logger enclosure (labeled comm. port).
The external port is located outside the logger enclosure (see Figure 2) and requires the weatherproofexternal communications cable (Part # CABLE-HWS2). Use this port to quickly connect to the logger
without having to open the logger door.
Launching the LoggerThere are several parameters you can enter when launching the Weather Station with the logger software.
To launch the logger, connect to it as described in Communicating with the loggeron page 11 and then
enter the following launch parameters. Note:If you are launching the logger with a U-Shuttle it will be
launched with the parameters you last entered in the logger software on the computer.
Launch parameter Description
Description Enter a description of the launch.
Battery type Make sure the appropriate battery type is selected, otherwise the batterygauge will not be accurate when checking the logger status.
Logging interval Set how often the logger will record data (for example every 30 minutes,hour, etc). The minimum logging interval is 1 second and the maximum is18 hours. Keep in mind that the faster the logging interval, the morequickly the batteries will be depleted.See the Estimating Battery Lifesection on page 14 for more details.
Sampling interval For use with sensors that support software-selectable measurementaveraging. The sampling interval sets how often sensors will takemeasurements between logging intervals. Check the sensors data sheetor manual to determine if your sensor supports measurement averaging.
When a sampling interval is used during launch, all the sampledmeasurements for the sensor are averaged together and the average isthen recorded as one data point at each logging interval. The individualdata points that comprise the average are not saved; only the final,averaged data point is saved.
Set the sampling interval to one of the predefined settings from 1 secondto 4 minutes. The sampling interval must be less than or equal to thelogging interval.Sampling rates shorter than 1 minute will reduce theloggers battery life.
Important:If you do not have any sensors that support measurementaveraging, set the sampling interval to Off as there will be no benefitand it will reduce battery consumption.
When to startlogging
Choose one of the following start modes for the logger:
Start logging now. The logger will start recordingmeasurements as soon as you are finished configuring thelaunch.
Delayed start. The launch is postponed until the exact date andtime you specify. You can add sensors to the logger any timebefore the specified start time.
Button start. The launch will not start until you press a button on
7/25/2019 Instructivo HOBO H 21 01
12/52
Section 2: Setup and Test
12 HOBO Weather Station Users Guide
Launch parameter Description
the logger. This allows you to configure the launch settings inadvance, but start the actual launch when you want withoutchoosing a specific date and time. You can add sensors any timebefore pressing the button on the logger.
Save settings for a later launch. Select this option when youwant to save the current launch settings for a future launch, butnot start the launch now (for example, prior to heading into thefield). This is useful if you plan on launching the logger with ashuttle, which doesnt allow you to change launch settings.
Wrap around whenfull
When this box is checked, new data will overwrite the oldest data in thelogger sequentially one sample at a time when the memory is full. Thelogger will continue logging indefinitely until either the logger is read outand stopped or the battery fails. If this box is not checked, the logger willstop logging when the memory is full and preserve acquired data. Formore information on memory, see the Logger memorysection on page45.
Edit sensor locations Give each sensor a name of up to 30 characters to help identify individualsensors.
Deployment notes Add up to 2000 characters of notes about the launch.
Reading out DataYou can read out data (offload) the logger with logger software. Connect to the logger as described in
Communicating with the loggeron page 11 and then read it out. If the logger is logging, you can choose
to either stop the logger before reading out or let it continue logging while reading out.
Readout speed depends on the method used to connect to the logger and the device being used. Typically,
a readout via PC interface cable with the computer will take about six minutes for full memory (512K of
data).
7/25/2019 Instructivo HOBO H 21 01
13/52
Section 2: Setup and Test
HOBO Weather Station Users Guide 13
BatteriesThe Weather Station requires four 1.5 V AA batteries. The logger is shipped with four alkaline batteries,
but it is also compatible with lithium batteries. For most applications, alkaline batteries are the preferred
solution because:
They are relatively inexpensive The battery gauge in the logger software will provide an accurate battery status
They have slightly more usable capacity than 1.5 Volt lithium batteries in temperateenvironments
In cold applications (below 0C [32F]) and hot applications (above 40C [104F]), lithium batteries will
generally outperform alkaline batteries. Alkaline batteries will still work in temperatures ranging from 40
to 50C (104 to 122F) and from -20 to 0C (-4 to 32F), however, they may not be the best choice. At
temperatures lower than -20C (-4 F) and higher than 50C (122F), alkaline batteries are unsuitable; use
lithium instead. If the temperature is variable across the extremes, use lithium batteries. Use the following
figure to help you choose the battery type based on the expected temperature range in your deployment.
Figure 3: Recommended battery type based on temperature
Note:
The logger is not designed to run with rechargeable or Carbon Zinc Heavy Duty batteries.
The use of types other than 1.5 Volt alkaline or lithium batteries may result in poor batteryperformance and erroneous battery state indication.
WARNING:Fire, Explosion, and Severe Burn Hazard.Do not mix battery types,
either by chemistry or age; batteries may rupture or explode. When replacing the
batteries, read and follow their disposal instructions; dispose of lithium batteries
according to local regulations. Do not dispose of batteries in fire. Never attempt to
recharge a lithium or alkaline battery. Do not heat the batteries above 185F (85C). Donot mutilate or rupture the battery housing. Lithium batteries may explode if the logger is
exposed to extreme heat or conditions that could damage or destroy the battery case. Do
not expose the contents of the battery to water.
= Recommended in this
temperature range
Lithium
Alkaline
= Works in this temperature
range, but not best choice
7/25/2019 Instructivo HOBO H 21 01
14/52
Section 2: Setup and Test
14 HOBO Weather Station Users Guide
Estimating Battery Life
Battery life will vary with:
Logging and sampling intervals (most important factor)
The number of sensors connected
Battery type
Operating environment
Use the following table to help you estimate how long the batteries will last (the run time) based on the
logging interval selected and the number of sensors connected. Note:The run times in this table assume
that the recommended battery type for the temperature range is being used.
LoggingInterval
SamplingInterval
1 to 5 sensors 5 to 10 sensors 10 to 15 sensors
1 second Off 30 to 50 days 20 to 40 days 15 to 30 days
1 minute Off 12 months 9 to 12 months 7 to 10 months
10 minutes 1 minute 12 months 12 months 9 to 12 months
15+ minutes 1 minute 12 months 12 months 9 to 12 months
Additional guidelines:
Turn off the sampling interval unless you have sensors that support measurement averaging. Atthe time of publication, only the 12-bit Temperature, Soil Moisture, Barometric Pressure,
Photosynthetically Active Radiation, and Solar Radiation smart sensors and the 4-20 mA and 0-5
Volt input adapters supported measurement averaging. Check the sensor manual to see if your
sensor supports measurement averaging.
Make sure the Use Before date on the battery housing is at least two years from the currentdate.
Alkaline batteries will lose up to 10% of capacity a year sitting on a hot shelf and can lose up to50% or more if cooked repeatedly (for example, stored on a car dashboard). Keeping batteries
in the refrigerator can reduce self-discharge to 1 to 2% per year, however, be sure to avoid
condensation forming on the batteries.
Use new batteries if you expect the deployment to require a substantial portion of battery lifebased on the table above.
Batteries are relatively inexpensive; dont take a chance with suspect batteries.
7/25/2019 Instructivo HOBO H 21 01
15/52
Section 2: Setup and Test
HOBO Weather Station Users Guide 15
Using a 9-Volt Battery
The Weather Station has an additional 9-volt battery connector adjacent to the four AA battery
compartment. Insert a 9-volt battery to temporarily maintain the power to the logger, which allows you to
replace aging AA batteries with fresh ones without interrupting logging.
Steps1. Unscrew the two thumbscrews on the battery door cover and remove the battery door.
2. Plug a 9 Volt battery into the battery connector to the right of the four AA batteries (observepolarity). Press firmly to make sure the connection is solid.
3. Remove the old AA batteries.
4. Insert the new AA batteries.
5. Remove the 9 Volt battery.
6. Replace the battery door cover and thumbscrews.
7. Verify that the logger is operating normally by checking that the Logging OK status light is
still blinking every two seconds.
While it is possible to run the logger with only a 9 Volt battery, it is not recommended for extended
deployment for the following reasons:
A 9 Volt battery will only last about one to two months (typical use).
The logger and its software do not provide an accurate battery level indication for a 9 Voltbattery.
The logger battery door cannot be used with a 9 Volt battery in place, it is possible that thebatteries will shake loose.
The 9 Volt battery cannot be used as a backup battery. The opposite actually occurs; the 9 Voltbattery will be used first, and then the AA batteries will be used.
Note:When changing batteries on the fly, the 9 Volt battery must have at least 7.5 volts remaining. If the
9 Volt battery has less than 7.5 volts, the battery gauge will not reset when new AA batteries are installed.
Use a fresh 9 Volt battery if you find that the battery gauge does not reset.
Using a 9-Volt Battery Eliminator
In some applications where AC power is available, it may be convenient to use a 9 Volt batter eliminator
to power the logger. 9 Volt DC supplies are commonly available from electronics supply stores (Radio
Shack catalog number 273-1552B). Minimum DC current should be 9 mA. If four AA batteries are also
used with the 9V battery eliminator, they will serve as back-up batteries. Note:The batteries will NOT be
charged and rechargeable batteries should not be used with the logger.
7/25/2019 Instructivo HOBO H 21 01
16/52
Section 2: Setup and Test
16 HOBO Weather Station Users Guide
Adding and Removing SensorsSmart sensors plug into the logger and collect data about various weather parameters. Before you bring
the logger and sensors to the field, it is important that you gather and test all the sensors. Specifically, you
should:
Plug in all the sensors you plan to use, Make sure they are communicating, and
Make sure the readings are valid.
To add a sensor, simply plug it into a sensor port on the logger. Follow these guidelines when adding
sensors:
Never add or remove sensors while the logger is recording data.Sensors should only beadded while the logger is stopped, when configuring the launch parameters with logger software,
or after configuration but before the start of logging in Delayed Start or Button Start modes (for
more information on these modes, see theLaunchingsection on page 11).
Any sensors added while the logger is recording data will be ignored.Logging will continuenormally for other sensors. If a sensor is removed while logging, the Sensor Error status light will
blink when the next logging interval is reached. The data for that sensor will then display as
missing or erroneous in readouts.
You cannot replace one sensor with a new sensor of the same type while logging.If youwould like to replace a sensor with another sensor of the same type (for example, swap a
temperature sensor with a new temperature sensor), it is necessary to read out the current data
from the logger and re-launch with the new sensor.
A maximum of 15 data channels can be used with one logger.Most sensors use one datachannel, which means the sensor is measuring one property only (for example a temperature
sensor uses one data channel that records information for temperature). However, there are some
sensors that measure more than one property, such as the combination temperature/RH sensor,
which uses two data channels.
To expand the number of sensors plugged in and data channels used, use 1-to-2 sensor
adapters(Part # S-ADAPT), which allow you to plug two sensors into one port. Note that the 1-
to-2 adapter is similar to a standard telephone splitter, but it has 6 conductors. Most telephone
splitters have only 4 conductors. A 4-conductor splitter may work, but it is not recommended
because the shield in the cable will not be properly grounded.
The logger can work with amaximum of 100 meters (328 feet) of smart sensor network
cable, which is the digital communications portion of the sensor cables. If you are using multiple
sensors, be sure to check the length of each smart sensor network cable reported in the Sensor
Manuals. Add them together and make sure theydo not exceed 100 meters(328 feet).
7/25/2019 Instructivo HOBO H 21 01
17/52
Section 3: Field Setup
HOBO Weather Station Users Guide 17
Section 3: Field Setup
After youve configured the logger and gathered the necessary materials for the field, you are ready to
assemble the tripod with the logger and sensors. This document includes:
Guidelines for typical field setup
Field preparation checklist
Tasks for setting up the Tri-pod
7/25/2019 Instructivo HOBO H 21 01
18/52
Section 3: Field Setup
18 HOBO Weather Station Users Guide
Guidelines for Typical Field Setup
Site Selection
Use the following guidelines to help you choose an appropriate site for setting up the Station and
protecting against field hazards.
When possible, select a location away from trees and buildings, particularly if you will be using therain gauge or wind speed sensors. Place the rain bucket at a distance away from obstructions that is
equal to at least three times the height of the nearest tree, building, or other obstruction, and the wind
speed sensor at a distance away from obstructions that is equal to at least five times the height of the
obstruction.
WARNING: Severe shock hazard. Do not set up the HOBO Station near power lines. Contactbetween the HOBO Station and power lines may result in a fatal shock, electrocution, or death.
Avoid placing the logger in extremely hot locations (such as on a dashboard or the roof of agreenhouse) and chronically wet locations (such as in a well or any place that is wet most or all of the
time). Also avoid rising water and flood zones.
Conduit is recommended when placing a sensor in or near the ground to protect against animals, lawnmowers, tractors, exposure to chemicals, etc.
Beware of rodents, birds, cattle, and other animals that can bite, peck, or trample the HOBO Station.
Avoid placing the sensors near falling rocks, dead trees, or other objects that could fall on the HOBOStation.
A Grounding Kit (Part # M-GKA) is required if using the Wind Speed or Wind Direction sensor withthe logger. A Grounding Kit is recommended if the logger will be placed in an exposed location on a
tripod or tower to reduce the chance of damage from atmospheric electrical activity.
If possible, avoid sites immediately adjacent to radio/television/microwave towers and equipment. Inrare situations, strong electromagnetic interference may result in sensor network errors.
Take note of the mounting considerations in the sensor manuals for additional guidelines relative to
the particular sensors you are using. For areas with winds greater than 50 mph, or if the rain gauge is attached to the top of the mast, use
the Guy Wire Kit (Part # M-GWA) and 1/2 inch Stake Kit (Part # M-SKA) to reduce wind-induced
vibration.
2 meter Tripod Tower Assembly(Part # M-TPB): You must set up the tower on level ground;there should be no ground slope. The legs on the 2 meter tower are non-adjustable. If the site you are
using is not level, then you will need to either level it or use shims to level the tripod. Be prepared to
dig if necessary. Suggested Mounting: Use 1/4 inch Stake Kit (Part #M-SKB).
3 meter Tripod Tower Assembly(Part # M-TPA):The maximum ground slope is 13 degrees. Thelegs on the 3 meter tower allow for limited adjustment on uneven ground. Be prepared to dig if
necessary if the slope is significant. Suggested Mounting: Use 1/2 inch Stake Kit (Part # M-SKA).
Onset recommends that two people set up most tripod systems. Some assemblies are heavy and areeasier to handle with two people.
Be sure to stabilize, level, and secure the tripod on firm ground. It may be necessary to adapt theinstallation to the existing site conditions as necessary (for example, if mounting the tripod on ice or
rock, you may need to use a masonry clamp to secure it).
If operating in a wet environment, place several desiccant packs in the logger and plug the vent holein the bottom of the logger enclosure to minimize moisture.
7/25/2019 Instructivo HOBO H 21 01
19/52
Section 3: Field Setup
HOBO Weather Station Users Guide 19
Mounting
It is possible to mount the logger and sensors on either a 1.5 meter or 3 meter mast (Part # M-MPB and
M-MPA respectively). The shorter mast is especially useful for smaller system configurations where you
are trying to minimize the size and visibility of the system.
There are many ways to install the mast depending on the site. Common mounting methods include
pounding the post into the ground, setting it into concrete, and bolting it to existing structures.
If you will be mounting PAR, wind speed, or rain gauge sensors, be sure that you install the mastvertically (using Mast Level, Part # M-MLA).
Use the Guy Wire Kit (Onset Part # M-GWA) to stabilize a tall mast. Use 1/2 inch stakes (Part # M-SKA) to secure the guy wires.
Mount the logger vertically and high enough that ground splash will not enter the vent on theunderside of the enclosure.
If using U-bolts, make sure they are for 1-5/8 inch pipe because that is the hole spacing on the loggermounting bracket.
If mounting the logger to a post or wall, note that it is 2.06 inches between the center of the holes in
the mounting brackets. It is recommended that you use 5/16 inch diameter bolts to mount the logger.
Installing Sensors
If running cables along the ground, we recommend running them through conduit to protect themfrom animals (some animals like to chew on the cables), lawn mowers, and being tripped on.
For information on protecting the sensors properly, refer to the sensor manuals.
Leave enough slack in the cables so that they can be routed into the logger.
If you are deploying multiples of the same sensor type, be sure to note the serial number on the cableassociated with each measurement location so you can interpret the data later.
7/25/2019 Instructivo HOBO H 21 01
20/52
Section 3: Field Setup
20 HOBO Weather Station Users Guide
Field Preparation ChecklistUse the following checklist to make sure you have all the necessary materials for setting up a HOBO
Station.
Task
Check that you received all the parts for the HOBO Station system as ordered.
Configure the logger. Install batteries and set up the logger for launch.
If you opened any parts: Double-check the packing lists to make sure no pieces are missing.
Attach the mounting feet to the logger. See the loggers manual.
If you are using the Solar Radiation Shield: Set up the Temperature and Temperature/RH sensors. There are severalsmall pieces required to connect these sensors to the shield that could easily get lost in the field. It is stronglyrecommended you install these sensors in the solar radiation shield before going to the field. See the sensor manual fordetails.
If you are using the barometric pressure sensor, attach it to the logger now. See the sensor manual for details.
Repack the logger and sensors for transit. It is strongly recommended that you use the original packaging when possible
because it is custom-designed to protect the weather station and its components.Gather the tools required for setup. Use the following checklists to make sure you have the necessary tools to set up thelogger in the field. Optional Items depend on your site needs.
Logger Rain Gauge Sensor
Item Item
1/2 inch wrench Mast level (Part # M-MLA) (optional; formounting on separate mast)
Flathead screwdriver Sledgehammer or post driver (optional;for mounting on separate mast)
Desiccant (optional) Eye protectionsafety glasses (if using
sledgehammer/post driver)Slotted screwdriver
Conduit (optional)
Light Sensor Wind Speed and/or Wind Direction Sensor
Item Item
Ladder (if deploying sensor above eyelevel)
7/16 inch wrench
Light sensor level (Part #M-LLA) Crescent wrench (or second 7/16 inchwrench)
Phillips head screwdriver #1 1.06 inch/2.00 inch hose clamps (ifmast mounting without cross arm)
Compass
7/25/2019 Instructivo HOBO H 21 01
21/52
Section 3: Field Setup
HOBO Weather Station Users Guide 21
Task
Gather the tools required for setup(continued)
Soil Moisture Sensor Temperature/RH or Temp Sensor
Item Item
Trenching shovel, spade, or flat bar Phillips head screwdriver #1 (if sensorsare not already installed)
Water (optional) Conduit (optional)
Barometric Pressure Sensor Pulse Input Adapter
Item Item
Hook and loop tape Two wire nuts
0-5 Volt Input Adapter 4-20 mA Input Adapter
Item Item
Hook and loop tape Hook and loop tape
3 m or 2 m Tripod with Mast (M-TPA or M-TPB) Cross Arm (M-CAA) or (M-CAB)
Item Item
1/2 inch wrench 1/2 inch wrench
Mast level (Part # M-MLA) Crescent wrench
Medium size wire cutters
Crescent wrench
Redimix cement (optional) Stake Kit (M-SKA) or (M-SKB)
Shovel (optional) Item
All purpose grease Sledgehammer
Tape measure Eye protectionsafety glasses
Tie wraps
3 m Mast (M-MPA) 1.5 m Mast (M-MPB)
Item Item
1/2 inch wrench Sledgehammer or post driver
Sledgehammer or post driver Eye protectionsafety glasses
Eye protectionsafety glasses (if usingsledgehammer/post driver)
Mast level (Part # M-MLA)
Mast level (Part # M-MLA) Redimix cement (optional)
Redimix cement (optional) Shovel (optional)
Shovel (optional) All purpose grease
All purpose grease Tape measure
Tape measure
7/25/2019 Instructivo HOBO H 21 01
22/52
Section 3: Field Setup
22 HOBO Weather Station Users Guide
Task
Grounding Kit (M-GKA) Guy Wire Kit (M-GWA)
Item Item
1/2 inch wrench Phillips head screw driver #2
Sledgehammer 1/2 inch wrench
Eye protectionsafety glasses Medium size wire cutters
Medium size wire cutters Crescent wrench
Solar Radiation Shield (M-RSA) Light Sensor Bracket (M-LBB)
Item Item
1/2 inch wrench 1/2 inch wrench
Phillips head screwdriver #1 (if sensorsarent already installed)
7/25/2019 Instructivo HOBO H 21 01
23/52
Section 3: Field Setup
HOBO Weather Station Users Guide 23
Tasks for Setting up the Tripod
Task 1: Assemble Tripod, page 24
Task 2: Install Grounding Kit, page 31
Task 3: Temporarily Install Upper Mast (Optional), page 32
Task 4: Mount Cross Arm (Optional), page 33
Task 5: Mount Upper Mast to Lower Mast, page 34
Task 6: Mount Logger to Upper Mast, page 35
Task 7: Install Guy Wire Kit (Optional), page 36
Task 8: Position and Level Sensors, page 38
Task 9: Final Setup, page 38
7/25/2019 Instructivo HOBO H 21 01
24/52
Section 3: Field Setup
24 HOBO Weather Station Users Guide
Task 1: Assemble Tripod
There are two types of tripods available: the 2 meter (Part # M-TPB) and 3 meter (Part # M-TPA). The 2
meter instructions begin on this page. The 3 meter instructions begin on page 27.
2 meter tripod/lower mast assembly instructions:
This is an example of a typical 2 meter tripod assembly with a Rain Gauge sensor mounted on separate1.5 meter mast (the Rain Gauge should be further from the tripod in the field than shown in this example).
Figure 4: 2 Meter Tri-pod
7/25/2019 Instructivo HOBO H 21 01
25/52
Section 3: Field Setup
HOBO Weather Station Users Guide 25
1. Open the 2 meter tripod and place it in an upright position.
2. Using a 1/2 inch wrench, build six nut and bolt assemblies (5/16-18) like the one shown below.
Figure 5: Nut and bolt assembly
3. Take one of the nut and bolt assemblies and insert it through a tri-clamp hole with the bolt head
facing outward.4. Loosely install a nut on the bolt to the inside of the tri-clamp.
Figure 6: Tri-clamp and bolts
5. Install the remaining five nut and bolt assemblies in the same manner for both upper and lowertri-clamps. Make sure the bolt assemblies on the upper and lower mast tri-clamps leave enough
room for the lower mast section to slip through.
6. Slide the lower mast from the top into the tri-clamps with the creased end of the mast facing up.The creases on the lower mast should face north and south.
7/25/2019 Instructivo HOBO H 21 01
26/52
Section 3: Field Setup
26 HOBO Weather Station Users Guide
7. Tighten the tri-clamp bolts by hand so that the mast is temporarily locked into position. Note:The lower mast can rest on the ground at this time. You will adjust the height of the lower mast
later.
Figure 7: 2 meter tripod - lower mast
8. Because the tripod for the 2 meter configuration has non-adjustable legs, you must verify that themounting surface area is level. If it is not, use shims or remove soil as needed. You can attach the
Post Level (Part # M-MLA) to the mast to verify that it is vertical as you level the surface. You
can also use the tri-clamp bolts to fine tune the vertical adjustment later after you adjust the
height of the mast.
9. Secure the tripod. Use either the -inch diameter stake kit (Part # M-SKB) or bolt the tripod tocement pads with -inch anchors. Install a stake or bolt through one of the holes on each of three
tripod feet.
10. If site conditions (high winds, etc.) warrant further stabilization of the tripod, use the Guy WireKit (Part # M-GWA). See Task 7: Install Guy Wire Kit on page 36.
7/25/2019 Instructivo HOBO H 21 01
27/52
Section 3: Field Setup
HOBO Weather Station Users Guide 27
3 meter tripod/lower mast assembly instructions:
This is an example of a typical 3 meter tripod assembly with a mast-mounted Rain Gauge sensor.
Figure 8: 3 meter tri-pod
7/25/2019 Instructivo HOBO H 21 01
28/52
Section 3: Field Setup
28 HOBO Weather Station Users Guide
1. Using 5/16 inch nuts, attach the three anchor plates to the three tripod foot brackets, with the large
holes to the outside. Tighten the nuts securely.
2. Attach the three leg U-bolts with saddle clamps, one each onto the outer legs about 20 cm (8 inches)
up from the anchor plates.
Figure 9: 3 meter lower tripod
3. Open the tripod and place it in an upright position.
4. Unfold the leg brace assembly and place the assembly flat on the ground.
Figure 10: 3 meter tripod leg brace
7/25/2019 Instructivo HOBO H 21 01
29/52
Section 3: Field Setup
HOBO Weather Station Users Guide 29
5. Attach each of the three inner legs to each of the leg U-bolt assemblies (5/16-18 inch) using the
inner stud of the U-bolt. To attach each inner leg, remove the nut from the inner stud, slide the leg
over the stud, and then tighten the nut finger.
Figure 11: Three meter tripod inner leg
6. Loosen the three lock nuts on the bolts on the upper and lower mast tri-clamp assemblies. Back the
three bolts out of the upper and lower mast tri-clamp assemblies so that the lower mast section can
be slipped down through the upper mast tri-clamps and into the lower mast tri-clamp with the
creased end of mast facing up. When the lower mast section is installed, hand-tighten the upper and
lower mast tri-clamps.
Figure 12: Three meter tripod lower mast
7. Install a Post Level (Part # M-MLA) on the lower mast as shown in the previous figure.
7/25/2019 Instructivo HOBO H 21 01
30/52
Section 3: Field Setup
30 HOBO Weather Station Users Guide
8. When the tripod is oriented on the site, secure one of the three tripod legs to its mounting location
and tighten the U-bolts on this leg.
9. Adjust the second leg to level in one direction and secure this leg.
10.Use the third leg to adjust the mast close to level.
11.When the mast is close to being level, secure the third leg.
12.Fine tune the mast level by sliding the U-bolts slightly up or down. Tighten all three leg tri-clamps
using a 1/2 inch wrench. Again, verify that the mast is level.
13.After checking level and orientation, tighten all upper and lower mast U-bolts and lock nuts.
14.Orient the lower mast creases so they face north and south.
15.Tighten the tri-clamp bolts so that the mast is locked into position. Note the lower mast should be
about 8 inches (20 cm) above the ground at this time (assuming that if you are using the wind
sensor, you want it to end up at 3 meters or almost 10 feet).
7/25/2019 Instructivo HOBO H 21 01
31/52
Section 3: Field Setup
HOBO Weather Station Users Guide 31
Task 2: Install Grounding Kit
This section explains how to install the grounding rod from the Grounding Kit (Part # M-GKA) and
attach it to the lower mast of either the 2 meter and 3 meter tripods.
1. Attach the ground wire to the lower mast of the tripod using the U-bolt assembly delivered withthe grounding kit.
2. Slide the ground rod clamp over the ground rod prior to driving it into the ground. This allowsyou to work with the clamp before the top of the rod is damaged from impact.
3. Using a sledgehammer, drive the ground rod into the ground as close as possible to the lowermast of the tripod.
4. Attach the ground wire to the ground rod. Cut off excess cable length and discard or recycle.
5. Tighten the clamp bolt.
Figure 13: Ground wire attachment
7/25/2019 Instructivo HOBO H 21 01
32/52
Section 3: Field Setup
32 HOBO Weather Station Users Guide
Task 3: Temporarily Install Upper Mast (Optional)
This section explains how to temporarily attach the upper mast to the tripod base. This allows you to
easily work on the upper mast while it is resting on the base of the tripod.
Note:If you prefer to permanently install the upper mast at this point because you will be able to reach
the fully assembled tower, go to Task 5 and then return to Task 4. Otherwise, follow these temporarysteps and then permanently attach the upper mast later.
1. If you will be using the Guy Wire Kit (Part # M-GWA), install the guy wire upper mast clampabout two-thirds up the upper mast. Tighten the clamp by hand to temporarily hold it in place.
You will need to adjust it later.
2. Stand the upper mast upright and tie a cable tie to one leg brace and one leg of the tripod usingthe cable ties supplied.Remove the cable ties after the cross arm and sensors are installed.
Figure 14: Upper mast (temporary)
7/25/2019 Instructivo HOBO H 21 01
33/52
Section 3: Field Setup
HOBO Weather Station Users Guide 33
Task 4: Mount Cross Arm (Optional)
Onset recommends that you use an Onset cross arm to mount the Wind Speed or Wind Direction sensor
because it keeps this sensor away from other sensors that could cause wind turbulence or wind shadows.
It is also the best way to ensure the sensor is vertical.
Steps1. Attach the cross arm to the upper mast using the two 1/4-20 x 2-3/4 inch hex head bolts. Mount
the cross arm on the side opposite the dimple (at the bottom of the upper mast) with the word
TOP on the upper surface of the cross arm.
2. Pass the two bolts with flat washers on them through the two holes on the cross arm and throughthe two holes at the top of the upper mast. Install a nylock nut on each bolt. Do not securely
tighten the bolts yet.
3. Install the mast plug into the upper mast top with the slot facing down and going over the two
bolts. Note:After the mast plug is installed, it should be flush with the top of the mast.
4. Tighten the two nuts equally.
Figure 15: Half cross arm (setup is same for full cross arm)
For directions on mounting the Wind Speed or Wind Direction sensor to the cross arm, see the sensor
manual.
7/25/2019 Instructivo HOBO H 21 01
34/52
Section 3: Field Setup
34 HOBO Weather Station Users Guide
Task 5: Mount Upper Mast to Lower Mast
NOTE: Onset recommends that two people work together to attach the upper mast to the lower mast.
1. Lightly grease the creased (upper) end of the lower mast.
2. While holding the upper mast securely, cut the cable ties that were temporarily holding the upper
mast to the lower mast.
3. Slide the upper mast onto the lower mast with the dimple going into the crease and oriented northif you are in the northern hemisphere, and south if you are in the southern hemisphere.
4. When the upper and lower masts are aligned, install the 1-5/8 inch U-bolt assembly onto theupper mast, placing it just above the dimple (about 2.5 cm or 1 inch from the upper mast bottom).
Tighten the clamp.
Figure 16: Upper and lower mast assembly
If you are using a Wind Speed or Wind Direction sensor and have not attached the cross arm, go to Task
4: Mount Cross Arm (Optional) on page 33.
7/25/2019 Instructivo HOBO H 21 01
35/52
Section 3: Field Setup
HOBO Weather Station Users Guide 35
Task 6: Mount Logger to Upper Mast
1. Using the two 1-5/8 inch U-bolt assemblies provided, mount the logger enclosure on the lower endof the upper mast in line with the upper mast dimple. The lower housing U-bolt can be placed
directly above the U-bolt holding the mast pieces together.
Note:When assembling the U-bolts, place the U-bolts around the upper mast, and install the
saddle clamp. Place the logger enclosure against the saddle clamps and screw on the top U-bolt
nuts only.
Figure 17: Logger Housing on Mast
2. If you are using the Guy Wire kit, position the logger enclosure so that it will not be in the way ofguy wires.
3. Attach the loggers ground wire to the lower housing U-bolt. Screw on the lower U-bolt nuts andthen tighten all the U-bolt nuts.
7/25/2019 Instructivo HOBO H 21 01
36/52
Section 3: Field Setup
36 HOBO Weather Station Users Guide
Task 7: Install Guy Wire Kit (Optional)
NOTE: If you are using the 2 meter tripod, you will need to attach the guy wires to three 1/2 inch stakes
(Part # M-SKA), which should be spaced evenly around the tripod at a distance of 3 to 4 m (10 to 13 ft)
from the mast.1. If you havent already done so, attach the upper mast tri-clamp to the upper mast. Orient the
eyebolts on the upper clamp so they align with each tripod foot or a 1/2 inch stake.
2. Attach one end of the guy cable to one eyebolt on the upper mast tri-clamp. Open the wire clampby loosening the screw on it. Place the clamp over the wire and tighten. Leave 2.5 cm (1 inch) of
wire protruding from the clamp.
Figure 18: Guy wire attachment
3. Hook one S hook and one turnbuckle onto the corresponding stake or leg.
Figure 19: Guying to 1/2 inch Stakes
Stake
7/25/2019 Instructivo HOBO H 21 01
37/52
Section 3: Field Setup
HOBO Weather Station Users Guide 37
Figure 20: Guying to 3 Meter tripod feet
4. Cut the guy cable so that it can be put through the loose end of the turnbuckle and the wire clamp.Make sure the turnbuckle is extended as shown in the figures before feeding the cable through.
5. Install the hooks, turnbuckles, and cables onto the other two stakes or tripod legs.
6. Tighten the three guy wires evenly by turning the turnbuckles.
7. Attach a Post Level (Part # M-MLA) on the upper mast to maintain the mast at vertical.
8. The guy wires should be taut when the installation is complete.
7/25/2019 Instructivo HOBO H 21 01
38/52
Section 3: Field Setup
38 HOBO Weather Station Users Guide
Task 8: Position and Level Sensors
Once the upper mast is locked in place and secured, position the sensors at the correct heights and check
that the Rainfall sensor and PAR sensors are level. See the sensor manuals for more details.
Task 9: Final Setup
1. Open the logger enclosure.
2. Pass all the sensor cable ends through the opening on the bottom of the logger enclosure.
3. Plug all the sensors with tabs facing up into the logger board located within the logger enclosure.It does not matter which connector you plug each sensor into. You can use a maximum of 15
channels and 100 meters (328 ft) of smart sensor cable.
Note:If you are installing more than ten sensors, you will need to install an adaptor (Part # S-
ADAPT) for each additional sensor. The adaptors fit into any of the connectors on the logger
board except the upper left connector and the connector second from the bottom on the right.
4. If you have a HOBO U-Shuttle or laptop on site, check current sensor readings to ensure thesensors are all working. For the HOBO Weather Station, note that you cannot check current
readings if the logger is waiting for a Button Start or a Delayed Start.
5. Neatly wrap all the sensor cables together and secure to the mast or tripod legs using cable ties.
6. Gather the excess cable and attach the cable ties to the upper mast behind the logger. Leave abouta 2 inch (5 cm) drip loop of cable below the logger.
Figure 21: Sensor Cables on Mast
7/25/2019 Instructivo HOBO H 21 01
39/52
Section 3: Field Setup
HOBO Weather Station Users Guide 39
7. Seal logger enclosure (HOBO Weather Station Only).
This step is especially important if the system is located in a wet environment.
Once you verify that the cables are secured in the inside of the logger box, take all the cables and
push them over to one side of the logger enclosure opening. Using the duct seal, make a ball that
is bigger than the logger enclosure opening, stuff the duct seal into the hole from the outside,
filling the void between the cables and the housing. This minimizes the possibility of dust,insects, and driving rain getting into the logger housing. Flare out the duct seal on the inside to
lock it place.
All cables should be neatly secured to the mast when complete.
NOTE: If you are using a HOBO Weather Station in a wet environment, place several dry
desiccant packs inside the logger enclosure (remove desiccant pack from its foil pouch before
installing)
8. Recheck that all the U-bolts, nuts, and clamps are secure for the entire system.
9. If you are using a Weather Station, launch the logger now. The U-30 is automatically launchedwhen powered-up.
10.Verify that the logger is operating properly. Refer to the logger user manual for LED indications.
11.Close the logger door. For the HOBO Weather Station, tighten the four cover screws.
Congratulations! The HOBO Station setup is complete.
7/25/2019 Instructivo HOBO H 21 01
40/52
Section 3: Field Setup
40 HOBO Weather Station Users Guide
7/25/2019 Instructivo HOBO H 21 01
41/52
Section 4: Maintenance
HOBO Weather Station Users Guide 41
Section 4: Maintenance
General Maintenance
Regular maintenance on the Weather Station is essential because it extends the life of the components andhelps to ensure the accuracy of recorded measurements. When the logger is deployed in the field,
potential damage can come from numerous sources, such as rodents, birds, vandals, and heavy storms.
Periodic check-ups in the field allow you to:
Check that the station is still set up and functioning as you intended
Check for damage
Minimize the impact of any damage found
This is particularly important if the logger is being deployed for a long period of time, such as several
months or a year. Regular checkups will help ensure that you are continuing to gather data as expected.
Performing a visual inspectionPeriodically perform a visual inspection of the Micro Station tower and logger enclosure. Check that:
Cables and wires are not damaged, cracked, cut, split, or broken
All the screws and bolts are tightly secured
The mast is still level (if in use)
The ground attachments are fastened to the tripod and logger (if in use)
There is no excess rust; replace rusty parts as necessary
7/25/2019 Instructivo HOBO H 21 01
42/52
Section 4: Maintenance
42 HOBO Weather Station Users Guide
Batteries
Checking Battery Status
There are two ways to check the battery status of the logger:
Check the Bat Low light on the logger. This light blinks when the battery has 25% or lesscapacity remaining.
Check the status with the logger software. For alkaline batteries, the status is displayed in thepercentage of capacity remaining. Lithium battery voltage is either listed as good, which
represents anywhere from 25 to 100% of capacity remaining, or empty, which represents 0 to
25% of capacity remaining. Lithium batteries have a relatively flat discharge curve, which means
the voltage does not vary much with use until they fail. Because of the uncertainty in capacity, it
is recommended that you start new launches with fresh lithium batteries that you know are at
100% rather than relying on old ones.
Changing Batteries
It is always recommended that you read out the logger before replacing batteries. If you replace the
batteries while the logger is logging, it will stop recording data. The data will not be overwritten,
however, until the next launch.
Follow these steps to change the batteries.
1. If the logger is currently logging, you will need to stop logging and readout the data. If you donot want to stop the logger, see the next section for instructions on how to use a 9-volt battery to
temporarily continue power while changing the batteries.
2. Unscrew the two thumbscrews on the battery door cover and remove the battery door.
3. Remove the old AA batteries.
4. Insert the new AA batteries.
5. Replace the battery door cover and thumbscrews.
6. Launch the logger using the computer or U-Shuttle.
7. Double-check the battery gauge in the logger software to make sure the batteries you installed arefull capacity.
8. Replace the battery door cover and thumbscrews.
7/25/2019 Instructivo HOBO H 21 01
43/52
Section 4: Maintenance
HOBO Weather Station Users Guide 43
Cleaning the Weather StationThe logger enclosure does not require regular cleaning. However, it is recommended that in dusty
locations you regularly clean these items:
Solar radiation shield.Wash with soap and water. Dirt/cobwebs obstruct air flow. Discoloration
can cause increased solar absorption, which can result in increased errors. Do not get thetemperature/RH sensor wet; see the temperature/RH sensor manual for instructions on cleaning it.
Light sensor.Make sure the drain hole is not plugged. If you need to clean the sensor head, seethe sensor manual for details and cautions on proper cleaning.
Rain gauge.Make sure there are no leaves or debris in the collector. Make sure the funnel is notplugged; use a cotton swab if necessary to clean.
Anemometer on wind speed sensor.Make sure the cups do not have any dirt/dust/cobwebs.Spray bearing with a light oil.
Logger enclosure.Remove dust with compressed air. Do not get water inside the enclosure.
Tower.Hose with fresh water if necessary.
Verifying Sensor AccuracyFor most sensors, Onset recommends that you test sensor measurement accuracies once a year. Onset
Computer can verify the accuracy of all sensors and recalibrate applicable sensors. For more details on
verifying sensor accuracy, refer to the user manual included with the sensors.
7/25/2019 Instructivo HOBO H 21 01
44/52
Section 4: Maintenance
44 HOBO Weather Station Users Guide
7/25/2019 Instructivo HOBO H 21 01
45/52
Section 5: Reference
HOBO Weather Station Users Guide 45
Section 5: Reference
MemoryThe logger uses non-volatile memory, which means it retains data indefinitely once power runs out.
Specifically, the logger uses a high-capacity Flash memory to store data, which can retain the data even
when the batteries are removed. This type of memory is very durable.
If the logger dies in the field from dead batteries, replace them and read out the logger immediately. Do
not relaunch the logger until the data has been recovered. If your logger is damaged, contact Onset
Computer because there is a chance the data can be recovered.
The logger contains 512K bytes of memory. Up to 10K of this memory is used to store the launch
configuration and user notes, leaving at least 502K bytes for data storage. The logger software
automatically estimates how long the logger will record data until the memory is full (the run time) based
on the logging interval and the number and type of sensors connected. In general, adding sensors decreases
running time while increasing the logging interval increases running time. In most applications, battery life
limits the duration of the data logging before memory capacity.
The following figure shows the expected run time for several logging intervals based on the total number
of bits in place, which is determined by adding together the bits per sample for each sensor measurement
parameter in your system. For example, a logger with the following sensors is using 70 total bits.
4 Temperature X 8 = 32
1 Wind Speed X 16 = 16
1 PAR X 10 = 10
1 Rain Gauge X 12 = 12
Total number of bits 70
7/25/2019 Instructivo HOBO H 21 01
46/52
Section 5: Reference
46 HOBO Weather Station Users Guide
At a logging interval of 5 minutes, the memory run time for a Weather Station using 70 bits would be
approximately 200 days (based on Figure 5). See the sensors manual for the number of bits each type of
sensor uses.
Figure 1: Memory run time
7/25/2019 Instructivo HOBO H 21 01
47/52
Section 5: Reference
HOBO Weather Station Users Guide 47
Time AccuracyWhen you launch a logger, its clock is set by the host computers time and time zone offset from UTC.
(UTC, or Coordinated Universal Time, is similar to Greenwich Mean Time.) The time zone offset makes
it possible to determine objective, non-local time. This prevents conflicts and confusion when you
relaunch a logger with a shuttle that may have been launched in a different time zone, or before a Spring
or Fall time change.
Once the logger is logging, it will keep fairly accurate time. However, the following may cause errors
with time reporting:
Host clock error. The most likely source of error is an incorrect time, or time zone setting, on thecomputer that launched the logger. Make sure the clock on your computer is set to the correct
date and time before launching the logger. One accurate resource is http://www.nist.time.gov.
Launch time loss. The logger may lose up to two seconds when it is launched. This is a one-timeerror that occurs as part of the start-up sequence and cannot be avoided.
Clock drift.The long-term time accuracy is a function of temperature. The worst-case error is 8parts per million (PPM) a week at 25 C, which is about 5 seconds per week. The error increases
as the temperature deviates from 25 C (see the figure below). If the temperature were a constant-20 C, the logger time error could be as much as 35 ppm (21 seconds per week).
The following graph shows the worst-case time error.
Figure 2: Worst-case time error
7/25/2019 Instructivo HOBO H 21 01
48/52
Section 5: Reference
48 HOBO Weather Station Users Guide
Resetting the ClockReading out the logger and relaunching it will reset the loggers clock. This is useful when your logger
has been running for a while and its clock needs to be reset. Make sure the computer clock is set
accurately before relaunching.
1. Exit HOBOware Pro and correct the computers clock.2. Restart HOBOware Pro.
3. Read out the logger, if you have not done so already.
4. Relaunch the logger.
7/25/2019 Instructivo HOBO H 21 01
49/52
Section 6: Troubleshooting
HOBO Weather Station Users Guide 49
Section 6: Troubleshooting
This section lists common problems you may encounter with the Weather Station and possible
resolutions.
Problem Resolution
Individual sensors arenot found or aremissing in the loggersoftware launch screen
If a sensor is removed and then immediately re-inserted, it may notbe auto-detected and therefore will not appear in the launch screen.Click the Reset or Add Sensor button in the launch screen.
Check for a loose connection between the sensor and the logger.
Make sure you havent exceeded the maximum of 15 sensorsconnected to the logger. Note that some sensors are dual sensorsand count as two, such as the temperature/RH sensor and the windspeed sensor. If you have more than 15 sensors, remove one or
more until you have 15 or less.
Make sure you havent exceeded 100 meters (328 ft) of networkcable.
All sensors are missingin the logger softwarelaunch screen
Remove all but one sensor, then check if the sensor appears in thelaunch screen. Continue to remove and re-insert the sensors one ata time until you find the bad sensor. If you find a bad sensor or ifnone of the sensors communicate, contact your Onset dealer orOnset Computer Corporation.
The error status light isblinking
If the error light is blinking in conjunction with the OK light, therewas a communication failure. The system has recovered, but youmay have an intermittent problem. Try checking the sensors one ata time to make sure they are all communicating. If you find a badsensor or if no sensor communicates, contact your Onset dealer orOnset Computer Corporation.
If the error light is the only light blinking, then at least one sensor iscurrently not communicating. Immediate investigation isrecommended. Look for a loose connection, which could cause badelectrical contact with a sensor. If found, remove the offendingsensor and check its wires and connector for damage and/or signsof moisture.
In general, it is recommended that you read out any data when thislight is blinking, investigate the problem, and re-launch the logger.
The battery low light is
blinking after thebatteries were replaced
Check the polarity; make sure the batteries are installed properly. It
is possible one cell is reversed.
Make sure you are using the correct battery type. The logger usesfour 1.5 volt AA alkaline or lithium batteries. The type must bespecified in the launch screen for the correct battery status.
Make sure you arent using a combination of alkaline and lithiumbatteries. Never mix battery types.
Check the battery expiration date; make sure it is at least two yearsfrom the current date. Batteries can lose significant capacity if
7/25/2019 Instructivo HOBO H 21 01
50/52
Section 6: Troubleshooting
50 HOBO Weather Station Users Guide
Problem Resolution
stored at elevated temperatures.
Check the voltage with a voltmeter. Alkaline batteries should be atleast 1.5 volt per cell when new; lithium batteries should be 1.6 voltper cell.
Batteries dieprematurely
Check for excessive moisture in the logger enclosure. Severeand/or repeated condensation in the logger enclosure can lead toshort circuits and battery failure. It may be necessary to addadditional sealing and/or desiccant to the logger enclosure toprevent condensation.
Check to make sure that both the logging and sampling intervalsare set for at least 1 minute or greater. Sampling/Logging intervalsfaster than 1 minute will rapidly deplete the battery. See the sectionon Estimating battery lifeon page 14 for more details.
Check for damaged wiring and/or sensors. Damaged cables orconnectors can result in complete or partial sort circuits that willrapidly drain batteries.
No status lights areflashing
The lights are very faint. In direct sunlight, shield the sun and checkagain.
Make sure the batteries are not dead. Batteries should have atleast 1 volt per cell.
The memory may be full. Read out (offload) data from the loggerand re-launch.
The logger may not have been launched. Check the status with thelogger software.
OK status light is notflashing
Make sure the logger is launched. If you configured the logger to launchwith a delayed start, check the date and time you selected and make
sure the Delay Start light is flashing. If you configured the logger tolaunch with a button start, press and hold the button on the logger for asecond until all the lights flash.
Data file contains errors If you are missing data for a particular sensor, check that the sensorwas properly installed. Remove and re-insert the sensor, and checkthat it can take current readings. If you find that it is not communicating,it may be a bad sensor. Contact your Onset dealer or Onset ComputerCorporation.
Data file cant beopened
The data file may have become corrupted. In rare circumstances, thedata file may have errors. Offload the logger again and try opening thefile again. If that does not work, contact your Onset dealer or OnsetComputer Corporation.
Logger is not found Check and replace the batteries.
Check communications cable connections.
7/25/2019 Instructivo HOBO H 21 01
51/52
Section 6: Troubleshooting
HOBO Weather Station Users Guide 51
7/25/2019 Instructivo HOBO H 21 01
52/52
Onset Computer Corporation
470 MacArthur Blvd.
Bourne, MA 02532
Top Related