Pantalla y Lentes
-
Upload
airenitrox -
Category
Documents
-
view
213 -
download
0
Transcript of Pantalla y Lentes
-
8/2/2019 Pantalla y Lentes
1/3
Kirby Morgan Dive Systems, Inc.1430 Jason Way Santa Maria, California 93455
Phone: 805/928-7772 Fax: 805/928-0342
www.KirbyMorgan.com email: [email protected]
KIRB
YMORGAN
D
IVESYSTEMS,Inc
.
2010 Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 100305021
WELD SHIELD ASSEMBLYPART # 525-400
FOR SUPERLITE-17 A/B, 17C, 17K, 27, HELMETS&
KMB-18A/B & 28B BAND MASKS
* Diver's point of view:* Lenses are available separately as
Part #525- 411 lens medium or Part #525- 412 lens dark
This assembly is designed to provide visual protection only.Please read the complete instruction sheet before proceeding
This Welding Shield Assembly will t the SuperLite 17A/B,C,K Su-
perLite 27B, the KMB-18A/B, and the KMB-28B. The SuperLite
and KMB port retainers are supplied with two plug screws which are
designed to protect the two threaded holes on the port retainer which
are provided for mounting the welding shield assembly.
BCAUTIONThe Weld Shield Mount Screw (6) is to only beused when the Weld Shield is mounted to the port
retainer. Use o this screw without the Weld Shieldwill result in damage to the fberglass port area.The plug screws should be replaced when theWeld Shield is not mounted to the port retainer.
INSTALLATION INSTRUCTIONS
1. Remove the two plug screws from the port retainer.
2. Insert the mount screws (6) through the spacer washers (7) and then
through the mount ears (10,11).
3. With the shield facing out of the helmet or mask, install and tighten
the two mount screws (6) into the port retainer.
Key Part No. Description Qty.
1 540-152 Weld Shield 1
2 510-400 Gasket 1
3 * Lens *
4 530-916 Stand off Post 4
5 535-402 Lens Clip 1
6 530-210 Mount Screw 2
7 530-527 Washer 2
8 530-917 Bolt 2
9 530-535 Washer 2
10 520-030 Teon Washer 4
11 540-146 Mount Ear, Right 1*
12 540-145 Mount Ear, Left 1*
13 530-530 Washer 2
14 530-408 Star Washer 2
15 530-320 Nut, Nyloc 2
16 530-022 Screw1 4
BWARNINGWe highly recommend that extreme cau-tion be exercised by all divers, regardless ohelmet or mask used, to avoid the possibil-ity o underwater explosions when cutting orwelding. It cannot be over stressed that any
underwater explosion can result in the injuryor death o the diver!
-
8/2/2019 Pantalla y Lentes
2/3
Kirby Morgan Dive Systems, Inc.1430 Jason Way Santa Maria, California 93455
Phone: 805/928-7772 Fax: 805/928-0342
www.KirbyMorgan.com email: [email protected]
KIRB
YMORGAN
D
IVESYSTEMS,Inc
.
2010 Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 100308002
BCAUTIONUse only KMDSI original replacement parts. The use of other manufacturers parts will inter-fere with the performance characteristics of your life support equipment and may jeopardize
your safety. Additionally, any substitutions will void any warranties offered by KMDSI. Whenordering spares, always insist on Kirby Morgan Genuine Parts.
WELD LENS KIT
PART # 525-403FOR SUPERLITE-17A/B, 17C 17K, 27, KM37, 47, 57 HELMETS&
KMB-18A/B & 28B BAND MASKS
PART # DESCRIPTION QTY.
510-577 Bumper 2520-030 Washer 2
530-210 Mount Screw 2
530-320 Lock Nut 2
530-408 Star Washer 2
530-527 Washer 2
530-535 Washer 2
535-901 Snap Ring 1
540-030 Mount Ear 2
550-025 Stud 2560-046 Weld Lens Frame 1
520-072 Sticker, Small oval KMDSI 1
-
8/2/2019 Pantalla y Lentes
3/3
Kirby Morgan Dive Systems, Inc.1430 Jason Way Santa Maria, California 93455
Phone: 805/928-7772 Fax: 805/928-0342
www.KirbyMorgan.com email: [email protected]
2010 Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 100308002
KIRB
YMORGAN
D
IVESYSTEMS,Inc
.
We highly recommend that extreme caution be exercised by all divers, regardless of helmet or
mask used, to avoid the possibility of underwater explosions when cutting or welding. It cannot
be over stressed thatany underwater explosion can result in the injury or death of the diver!
PART # 525-403
WELDING LENS ASSEMBLY
1
2
3
4
5
6
530-320
530-535530-408
540-030
530-210
530-527
Nut, Lock
WasherStar Washer
Mount Ear
Mount Screw
Washer
2
22
2
2
2
Key Part No. Description Qty.
7
89
10
11
12
520-030
550-025560-046
535-901
510-577
525-403
Washer
StudWeld Lens Frame
Snap Ring
Bumper
Welding Lens Ass'y Complete
Lenses are available seperately as Part #525- 405 lens light, #525- 406 lens med.,#525- 407 lens dark
KMDSI has introduced a new weld lens frame which now has the Kirby Morgan name on the
front. These frames require a new, smaller bumper (11), part number 510-577. The older
larger style bumper, part number 510-576 ts in the weld lens frames without the Kirby
Morgan name. The frame (9) part numbers did not change
2
2
1
1
2
1
Caution - WarningThe Weld Lens Mount Screw (5) is to only be used when the Weld Lens is mounted to the port retainer. Use of this
screw without the Weld Lens will result in damage to the berglass port area. The plug screws should be replacedwhen the Weld Lens is not mounted to the port retainer.
This Welding Lens Assembly will t the SuperLite 17A/B, SuperLite 27B, the KMB-18A/B, and the KMB-28B. The SuperLite a
KMB port retainers are supplied with two plug screws which are designed to protect the two threaded holes on the port retainer which a
provided for mounting the welding lens assembly.
This assembly is designed to provide visual protection only. Please read the complete instruction sheet before proceeding.
INSTALLATION INSTRUCTIONS
1. Remove the two plug screws from the port retainer.
2. Insert the mount screws (5) through the spacer washers (6) and then through the mount ears (4).
3. With the rubber bumpers (11) facing the inside of the helmet or mask, install and tighten the two mount screws (5) into the port retainer.
4. Tighten the two locknuts (1) on the ends of the hinge studs (8) so that the Welding Lens Assembly can be ipped up, but will not fall
down from its own weight.
Key Part No. Description Qty.